Abstract:Wire and arc additive manufacturing (WAAM) has emerged as a highly promising technique for manufacturing large-scale steel structural elements. However, the distinct mechanical properties of WAAM steel could potentially lead to different performance of WAAM steel bolted connections compared to the traditional steel bolted connections. This study aims to investigate the material properties of WAAM steel and the structural behaviours of WAAM steel bolted connections, focusing on the effects of print layer orientation and connection plate geometrical dimensions. A total number of 24 WAAM steel coupon specimens with three different print layer orientations and 36 WAAM double-shear bolted connections with two print layer orientations and different geometric dimensions were designed, fabricated and tested under monotonic tension. These specimens were measured using a 3D laser scanner and Digital Image Correlation (DIC) was adopted to measure the structural response during testing. The impact of print layer orientations on WAAM material properties and the effects of WAAM material properties on bolted connections were analysed and discussed. The current design codes for traditional steel bolted connections were evaluated against the test results of WAAM steel bolted connections. The study found that the print layer orientations of WAAM steel plates initiated an anisotropic material property of the coupon specimens, demonstrated by the differences in ultimate tensile strength and strain of specimens with different print layer orientations. Five failure modes, including net section tension, shear-out, bearing, end-splitting, and block shear failure were observed for the bolted connections. The material anisotropy further affects the performance of the bolted connections, though in the same dimensions, 28% of the specimens presented different failure modes due to the different print layer orientations. The effectiveness of current steel design standards was compromised by inaccurate predictions of failure modes due to the distinct end-splitting failure mode and the effects of material anisotropy, though the predictions of the ultimate capacities of the WAAM lap shear specimens were relatively accurate.

Hydraulic Bulging and Failure Analyses of Wire Arc Additive Manufactured Steel Tubes

Structural Behaviour and Design of Wire Arc Additively Manufactured Bolted Connections with Thick Plates

Experimental Study on Wire and Arc Additively Manufactured Steel Double-Shear Bolted Connections

Mechanical Properties, Microstructural Characteristics and Heat Treatment Effects of WAAM Stainless-Steel Plate Material

Improving mechanical strength and isotropy for wire-arc additive manufactured 304L stainless steels via controlling arc heat input

Numerical Analysis and Design of Concrete-Filled Wire Arc Additively Manufactured Steel Tube under Axial Compression

Test and Analysis of the Interfacial Bond Behaviour of Circular Concrete-Filled Wire-Arc Additively Manufactured Steel Tubes

Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses

Microstructural and Mechanical Property Analysis of High-Strength Low-Alloy Steel Tubes Fabricated Using Wire Arc-Directed Energy Deposition Technique

Evaluation of Formability and Material Characteristics of Aluminum Alloy Friction Stir Welded Tube Produced by a Novel Process

Mechanical properties of wire arc additive manufactured carbon steel cylindrical component made by gas metal arc welding process

A study on wire arc additive manufacturing of 308L austenitic stainless steel cylindrical components: Optimisation, microstructure and mechanical properties

Fatigue crack growth behaviour of wire arc additively manufactured steels

Mechanical properties and microstructure characteristics of wire arc additively manufactured high-strength steels

Testing, analysis and design of wire and arc additively manufactured steel bolted connections

Mechanical properties of wire arc additive manufactured carbon steel cylindrical component made by cold metal transferred arc welding process

Experimental Application of Robotic Wire-and-Arc Additive Manufacturing Technique for Strengthening the I-Beam Profiles

Analysis of Warping Failure in Tube Hydro-Forging

Crushing performance of cost-effective tubular components of AA 5083-O fabricated through friction stir welding process for automotive application

Printing High-Strength High-Elongation Al4043 Alloy Using UNS A94043 Welding Wires through Wire Arc Additive Manufacturing

An approach to tunable advanced high-strength steel fabrication through multi-wire arc additive manufacturing (M-WAAM)