Abstract:TiAl intermetallic compounds, as a new kind of high-performance light-weight structural material, are widely applied in many fields. Titanium carbide (TiC) as the reinforcing phase could improve the mechanical properties, wear resistance, and heat-resistance stability of TiAl intermetallic compounds. Ti(Al, C) mixture powders were deposited by cold spraying at gas temperature of 250 °C, 450 °C, and 550 °C. Then, Ti(Al, C) coatings were annealed at temperatures of 650 °C for different times and following holding at 1100 °C for 3 h. The microstructure, microhardness, fracture toughness, and abrasive wear of Ti-Al composite coatings were investigated. The research results were that the particle size of mixture powders decreased as the ball milling time prolonging. Ti(Al) solid solution appeared in the mixture powders as the milling time increased to 30 h. The average porosity of the coating sprayed at 550 °C was the lowest (0.85%). The as-sprayed coatings exhibited the same phase compositions with the mixture powders. The coating sprayed at gas temperature of 550 °C has the highest microhardness and the lowest weight loss. Ti-Al intermetallic was in-situ synthesized after annealing at 650 °C. The average porosity of the annealed coating (sprayed at 450 °C) was the lowest. The content of Ti-Al intermetallic compounds of the annealed coating sprayed at 450 °C is the highest. The X-ray diffraction (XRD) analysis results are consistent with the EDS analysis of the annealed coatings after annealing at 650 °C. Ti-Al intermetallic compounds were almost completely formed in the three kinds of the coatings after annealing at 650 °C for 20 h and following holding at 1100 °C for 3 h. TiAl and TiAl3 intermetallic phases were in-situ synthesized in the coatings based on the energy dispersive spectroscopy (EDS) and XRD analysis. TiC was also in situ synthesized in the coatings as the annealing temperature increased to 1100 °C. The annealed coating (sprayed at 450 °C) has the highest microhardness, fracture toughness, and wear resistance properties after annealing at 1100 °C for 3 h.

Reactive Synthesis of Porous Nanolaminate Ti3(Si,Al)C2 Intermetallic Compound

In-situ Synthesis of Nanocrystalline TiC Powders, Nanorods, and Nanosheets in Molten Salt by Disproportionation Reaction of Ti(II) Species

In Situ Synthesis of Ti2AlC–Al2O3/TiAl Composite by Vacuum Sintering Mechanically Alloyed TiAl Powder Coated with CNTs

Direct Synthesis of Controllable Microstructures of Thermally Stable and Ordered Mesoporous Crystalline Titanium Oxides and Carbide/Carbon Composites

Porous TiFe2 intermetallic compound fabricated via elemental powder reactive synthesis

Synthesis and characterization of mesoporous TiC nanopowder/nanowhisker with low residual carbon processed by sol–gel method

Reactive Synthesis of Polycrystalline Ti3AlC2 and Its Sintering Behavior

Facile Electrosynthesis of Ti3AlC2 and Its Derived Porous Carbon in Molten Salt

A possible mechanism on synthesis of Ti3AlC2

Porous TiAl alloys fabricated by sintering of TiH 2 and Al powder mixtures

The synthesis of high purity Ti3AlC2 MAX phase via molten salt method

A novel simple method to stably synthesize Ti3AlC2 powder with high purity

Formation Mechanisms of Ti2AlC and Ti3AlC During Solid-State Sintering Between Multilayer Graphene and TiAl Alloy Composite

Reactive Synthesis for Porous (Mo2/3Y1/3)2AlC Ceramics through Mo, Y, Al and Graphite Powders

Reactive Synthesis of Porous Cu3si Compound

Synthesis and Mechanical Properties of In-Situ Hot-Pressed Ti3SiC2 Polycrystals

Porous Ti3AlC2 MAX phase enables efficient synthesis of Ti3C2Tx MXene

Reaction Synthesis of Ti3SiC2 from Mixture of Elemental Powders

Facile Synthesis of Ti3SiC2 Powder by High Energy Ball-Milling and Vacuum Pressureless Heat-Treating Process from Ti–TiC–SiC–Al Powder Mixtures

Fabrication of in situ Ti5Si3/TiAl composites with controlled quasi-network architecture using reactive infiltration

Microstructure, Microhardness, Fracture Toughness, and Abrasive Wear of In-Situ Synthesized TiC/Ti-Al Composite Coatings by Cold Spraying Combined with Heat Treatment