Abstract:Axial ultrasonic vibration-assisted face grinding (AUVAFG) of SiC has the characteristics of high efficiency and serious damage. With the aim of solving the problem of serious surface damage in AUVAFG of SiC ceramics, a composite ultrasonic vibration-assisted face grinding (CUVAFG) method involving axial vibration and elliptic vibration is proposed, which not only ensures the high efficiency but also maintains high quality of the machined surface. In this paper, the grinding forces and the surface quality were investigated by conducting comparative experiments on axial and composite ultrasonic vibration-assisted face grinding using a single diamond. The effects of ultrasonic vibration amplitude and wheel speed on grinding forces, ground surface roughness, and ground surface morphology were analyzed to reveal the brittle-ductile removal behavior of SiC ceramics during the micro-cutting process caused by elliptic ultrasonic vibration. The results show that CUVAFG can effectively reduce the grinding forces by about 15%, reduce the ground surface roughness by approximately 40.7%, and induce ductile removal to acquire good surface finish with predominantly facets in comparison to AUVAFG. More specifically for CUVAFG, with increased elliptic ultrasonic vibration amplitude along the long axis, the grinding forces are reduced by minor amplitude, but remain constant in the case of major amplitude. When the elliptic vibration amplitude is close to the critical chip thickness of brittle-ductile transition, the number of facets on workpiece surface is the highest, but the grinding forces and the surface roughness are relatively low. Meanwhile, with the increase of wheel speed, the number of facets and the proportion of ductile removal are both increased, but the grinding forces and the surface roughness are decreased. In order to realize low-damage machining of SiC ceramics by CUVAFG, it is suggested to keep the elliptic ultrasonic vibration amplitude around the critical chip thickness of brittle-ductile transition and use minor axial ultrasonic vibration amplitude and high wheel speed to achieve lower grinding forces and good surface quality.

Grinding Wheel for Low-Damage Grinding of Silicon Wafers and Its Grinding Performance

High surface integrity fabrication of silicon wafers using a newly developed nonwoven structured grind-polishing wheel

Mechanical effect of abrasives on silicon surface in chemo-mechanical grinding

Two Dimensional Ultrasonic Vibration Assisted Chemo-Mechanical Grinding of Si Wafer

Wear Characteristics of Diamond Wheel in Elliptical Ultrasonic Assisted Grinding (euag) of Monocrystal Silicon

Improved grinding performance of SiC using an innovative bionic vein-like structured grinding wheel optimized by hydrodynamics

High Efficiency Precision Grinding of Micro-structured SiC Surface Using Laser Micro-structured Coarse-Grain Diamond Grinding Wheel

Ductile deformation and subsurface damage evolution mechanism of silicon wafer induced by ultra-precision grinding process

Study on the Resin Bond Diamond Grinding Wheel Used for Ultra-Precision Back Grinding Silicon Wafer

Performance Improvement of Chemo-Mechanical Grinding in Single Crystal Silicon Machining by the Assistance of Elliptical Ultrasonic Vibration

C13 Wear Characteristics of Grinding Wheel on Spiral Ultrasonic Assisted Grinding of Sapphire Wafer : Topographic Features of Vitrified Diamond Wheel

The study of the resin-bond diamond wheel for IC silicon wafer nanoscale roughness back grinding

A New Two-Dimensional Ultrasonic Assisted Grinding (2D-Uag) Method and Its Fundamental Performance in Monocrystal Silicon Machining

Grinding performance evaluation of SiC ceramic by bird feather-like structure diamond grinding wheel

Novel Vitrified-Bond Ultra-Fine Grinding Technology for SiC Polishing

Experimental Investigation on Materials Removal Mechanism During Grinding Silicon Carbide Ceramics with Single Diamond Grain

Effect of grinding damage on cutting force and ductile machining during single grain scratching of monocrystalline silicon

Experimental investigation on the feasibility of high-efficiency and precision grinding of silicon carbide ceramics with monolayer brazed diamond wheel

Axial and composite ultrasonic vibration-assisted face grinding of silicon carbide ceramics: grinding force and surface quality

2205 Grinding Performance of Spiral Ultrasonic Assisted Grinding for Monocrystal Sapphire Using Vitrified Diamond Wheel

Analysis of the high-efficiency and low-damage abrasive processing mechanism for SiC based on the SPH simulation of single-grain indentation and scratching