Abstract:Copper sulfides (Cu2–xS) have become potential thermoelectric (TE) materials because of their high element abundance, low toxicity, and high performance. A series of Cu1.8–2xBi2xS1–3xSe3x (0 ≤ x ≤ 0.03) bulks were fabricated using mechanical alloying and spark plasma sintering. The main Cu1.8S phase was obtained in all compositions of 0 ≤ x ≤ 0.03, and marginal Cu1.96S and Cu2S phases were detected at 0.02 ≤ x ≤ 0.03, which is attributed to the volatilization of sulfur and selenium. Benefiting from the introduced extra electronics by Bi3+ doping, the carrier concentration was optimized in 2.31×1021 cm–3. Multiscale defects introduced by Bi–Se co-doping, including secondary phases, micropores, and point defects (BiCu••, SeS×, and VS••), strongly scattered the phonons, leading to a drastically decreased thermal conductivity from 2.71 W m–1 K–1 for Cu1.8S at 773 K to 0.80 Wm–1 K–1 for Cu1.74Bi0.06S0.91Se0.09. A maximum ZT of 0.78 was achieved for Cu1.74Bi0.06S0.91Se0.09 at 773 K, which is 144% higher than that of Cu1.8S (0.32). The current stress test confirms that Bi doping could improve the stability of Cu1.8S by suppressing the Cu ion migration. Our work demonstrates that Bi–Se co-doping is an effective way to enhance the TE properties for Cu1.8S.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.2c00414.SPB model calculation of our work; method for the current stress test; calculation formulas for ZTeng and ηmax; temperature dependence of thermal properties of the Cu1.8–2xBi2xS1–3xSe3x (x = 0, 0.01, 0.02, 0.25, 0.03) samples; and repeatability test of electrical properties for the Cu1.74Bi0.06S0.91Se0.09 sample (PDF)This article has not yet been cited by other publications.

Attempting to Realize N-Type BiCuSeO

Realizing N-Type BiCuSeO Through Halogens Doping

Realization of N-Type and Enhanced Thermoelectric Performance of P-Type BiCuSeO by Controlled Iron Incorporation

Enhancing thermoelectric performance of n-type Bi6Cu2Se4O6 through introducing transition metal elements

Thermoelectric Properties of Strained -Cu<sub>2</sub>Se

Synergistically enhanced thermoelectric properties in n-type Bi6Cu2Se4O6 through inducing resonant levels

Isotropic Thermoelectric Performance of Layer-Structured n-Type Bi2Te2.7Se0.3 by Cu Doping

Thermoelectric Property Studies on Cu‐Doped N‐type CuxBi2Te2.7Se0.3 Nanocomposites

Enhanced thermoelectric performance of n-type Bi 2 Se 3 doped with Cu

Enhanced Thermoelectric Performance of BiCuSeO Via Dual-Doping in Both Bi and Cu Sites

Quasi-layered Crystal Structure Coupled with Point Defects Leading to Ultralow Lattice Thermal Conductivity in n-Type Cu 2.83 Bi 10 Se 16

Remarkable Enhancement in Thermoelectric Performance of BiCuSeO by Cu Deficiencies.

Enhanced thermoelectric performance of BiCuSO by Pb doping and Se alloying

Isotropic Thermoelectric Performance of Layer-Structured n-Type Bi 2 Te 2.7 Se 0.3 by Cu Doping

ChemInform Abstract: Enhanced Thermoelectric Performance of N‐Type Bi2Se3 Doped with Cu.

Electrical and Thermal Transport Properties of <i>n</i> ‐type Bi <sub>6</sub> Cu <sub>2</sub> Se <sub>4</sub> O <sub>6</sub> (2BiCuSeO + 2Bi <sub>2</sub> O <sub>2</sub> Se)

Enhanced Thermoelectric Properties and Electronic Structures of P-Type BiCu1−xAgxSeO Ceramics

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu 1.8 S via Carrier Concentration Regulation and Multiscale Phonon Scattering

Thermoelectric Optimization of n-Type AgBiSe 2 via Se Vacancy Control and Transition-Metal Doping

Realizing p-type performance in low-thermal-conductivity BiSbSe 3 via lead doping

Defect Engineering for Realizing P-Type AgBiSe2 with a Promising Thermoelectric Performance