Abstract:This study presents a colloidal synthesis method to produce thermoelectric Cu3SbSe4 nanocrystals with high yield. Pb doping is employed to increase carrier concentration and effective mass, confirmed by experimental studies and theoretical calculations. Additionally, lattice distortions and other intriguing nanostructures are found to significantly reduce thermal conductivity. Consequently, the thermoelectric figure of merit zT is greatly enhanced. Developing cost‐effective and high‐performance thermoelectric (TE) materials to assemble efficient TE devices presents a multitude of challenges and opportunities. Cu3SbSe4 is a promising p‐type TE material based on relatively earth abundant elements. However, the challenge lies in its poor electrical conductivity. Herein, an efficient and scalable solution‐based approach is developed to synthesize high‐quality Cu3SbSe4 nanocrystals doped with Pb at the Sb site. After ligand displacement and annealing treatments, the dried powders are consolidated into dense pellets, and their TE properties are investigated. Pb doping effectively increases the charge carrier concentration, resulting in a significant increase in electrical conductivity, while the Seebeck coefficients remain consistently high. The calculated band structure shows that Pb doping induces band convergence, thereby increasing the effective mass. Furthermore, the large ionic radius of Pb2+ results in the generation of additional point and plane defects and interphases, dramatically enhancing phonon scattering, which significantly decreases the lattice thermal conductivity at high temperatures. Overall, a maximum figure of merit (zTmax) ≈ 0.85 at 653 K is obtained in Cu3Sb0.97Pb0.03Se4. This represents a 1.6‐fold increase compared to the undoped sample and exceeds most doped Cu3SbSe4‐based materials produced by solid‐state, demonstrating advantages of versatility and cost‐effectiveness using a solution‐based technology.

Doping of thermoelectric PbSe with chemically inert secondary phase nanoparticles

Light Element Doping and Introducing Spin Entropy: an Effective Strategy for Enhancement of Thermoelectric Properties in BiCuSeO.

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4

Enhancement of thermoelectric performance of Cu 1.98 Se by Pb doping

Enhancing Thermoelectric Performance of p-Type PbSe through Suppressing Electronic Thermal Transports

Robustly Boosting Thermoelectric Performance of N‐Type PbSe via Lattice Plainification and Dynamic Doping

Optimizing the thermoelectric performance of n-type PbSe through dynamic doping driven by entropy engineering

Preparation of Heavily Doped P-Type PbSe with High Thermoelectric Performance by the NaCl Salt-Assisted Approach

Enhanced Thermoelectric Performance of PbSe Co-Doped with Ag and Sb

Unconventional Doping Effect Leads to Ultrahigh Average Thermoelectric Power Factor in Cu 3 SbSe 4 ‐Based Composites

Boosting the Thermoelectric Performance of PbSe from the Band Convergence Driven By Spin‐Orbit Coupling

Lattice expansion enables interstitial doping to achieve a high average ZT in n‐type PbS

Nanoporous PbSe–SiO2 Thermoelectric Composites

Synergistically Optimized Electron and Phonon Transport of Polycrystalline BiCuSeO via Pb and Yb Co-Doping

Complex lattice occupation of copper leading to enhanced thermoelectric performance in n-type PbSe

Synergistic Optimization of Thermoelectric Performance in SnSe2 through co-doping: Anionic Vacancy Formation and Band Engineering

Enhanced Thermoelectric Performance of N‐Type PbSe Through Semi‐Coherent Nanostructure by AgCuTe Alloying

Synergistically optimizing carrier and phonon transport properties in n-type PbTe through I doping and SnSe alloying

Modulation Doping Leads to Optimized Thermoelectric Properties in n‐Type Bi6Cu2Se4O6 due to Interface Effects

Enhancing the Thermoelectric Performance of Cu2se Via Ag Doping

Thermoelectric properties of n-type transition metal-doped PbSe