Abstract:A comprehensive research project consisting of pilot-scale combustion testing and long-term laboratory corrosion study has been performed. A pilot-scale combustion facility was modified to enable burning of pulverized coals under the conditions typical for coal-fired utility boilers. Eight United States (U.S.) coals were selected for this investigation, with the test conditions for all coals set to have the same heat input to the combustor. In addition, the air/fuel ratio was controlled so that approximately 3% excess oxygen was attained in the combustion gas at the furnace outlet, a location equivalent to the furnace exit of commercial boilers. During each pilot-scale combustion test, extensive online measurements of the flue gas compositions were performed. In addition, deposit samples were collected at the same location for chemical analyses. This information characterized well the combustion environments adjacent to the superheaters and reheaters of utility boilers burning different U.S. coals. The gas and deposit compositions were then simulated in a series of 1000-hour laboratory corrosion tests in which the corrosion performances of different alloys were evaluated at 704oC (1300oF). Results of this laboratory study led to better understanding of the corrosion mechanisms operating on superheaters and reheaters in coal-fired boilers due to the mutual presence of sulfur and chlorine in coal. A new corrosion mechanism, i.e., “Active Sulfide-to-Oxide Corrosion Mechanism,” accounts for the rapid corrosion attack on low-alloy ferritic steels and lower-grade stainless steels resulting from the formation of iron chloride (FeCl2) vapor and associated cycling reactions. For higher alloys containing sufficient chromium, the attack is dominated by Hot Corrosion in the presence of a fused salt. In addition, two stages of the hot corrosion mechanism have been elucidated here in detail. The initiation of hot corrosion attack induced by molten sulfate may involve Stage 1 “acidic” fluxing and re-precipitation of the protective scale formed initially on the deposit-covered alloy surfaces, followed by Stage 2 Hot Corrosion dominated by “basic” fluxing and re-precipitation after the scale is locally penetrated by the fused salt.

Investigation of Fireside Corrosion at Water-Cooled Wall from a Coal-Fired Power Plant in China

Effect of Fouling Layer (Acid–Ash Reaction) on Low-Temperature Corrosion Covering Heating Surface in Coal-Fired Flue Gas

Revealing the Effect of O2, SO2 and H2O in Supercritical CO2 on the Corrosion Behavior of 316L Steel at Elevated Temperature

In-situ sampling investigation of deposition and corrosion of convective heating surfaces in a grate type municipal solid waste incineration plant: a case study

High-temperature corrosion of water-wall tubes in oxy-combustion atmosphere

Water Wall Tubes’ High Temperature Corrosion Root Cause Investigation: A 300 MW Level Boiler Case

STUDY ON MIGRATION AND DEPOSITION BEHAVIOR OF MINERAL SUSTANCES IN COAL BURNING INSIDE THE FURNACE

The Transformation Mechanism of H2S Beside the Water Wall under Reducing Condition

Analysis and Solution of High-temperature Corrosion for a 1000 MW Ultra-supercritical Boiler

Numerical investigation of boiler waterwall corrosion by integrated tube temperature prediction and sulfur evolution model

High-temperature corrosion behaviours of nickel–iron-based alloys with different molybdenum and tungsten contents in a coal ash/flue gas environment

The Transformation Mechanism of H<sub>2</sub>S beside the Water Wall under Reducing Condition

The Mineralogy Analysis Of Ash Deposition In Refractory Zones In A W-Flame Boiler

High-Temperature Corrosion Mechanisms for Selected Iron and Nickel-Based Alloys Exposed to Sulfur and Chlorine-Containing Environments

Experimental study on ash deposition and corrosion in a CFB boiler co-firing biomass with coal

Fireside Corrosion Behaviors Of Super304h And Hr3c In Coal Ash/Gas Environment With Different So2 Contents At 650 Degrees C

Experment of the corrosion behavior of Super304H steel in simulative coal ash/flue gas environment at 650 ℃

Investigation on ash fouling formation of induced fan blade and heat exchanger surface in a 1000MW coal-fired power plant

Fireside Corrosion Behaviors of Super304H and HR3C in Coal Ash/Gas Environment with Different SO 2 Contents at 650 °C

Effect of Alloying Chemistry on Fireside Corrosion Behavior of Ni–Fe-Based Superalloy for Ultra-supercritical Boiler Applications

Analysing the Cause of High Temperature Corrosion in the Superheaters of Power Plant Systems