Abstract:A comprehensive research project consisting of pilot-scale combustion testing and long-term laboratory corrosion study has been performed. A pilot-scale combustion facility was modified to enable burning of pulverized coals under the conditions typical for coal-fired utility boilers. Eight United States (U.S.) coals were selected for this investigation, with the test conditions for all coals set to have the same heat input to the combustor. In addition, the air/fuel ratio was controlled so that approximately 3% excess oxygen was attained in the combustion gas at the furnace outlet, a location equivalent to the furnace exit of commercial boilers. During each pilot-scale combustion test, extensive online measurements of the flue gas compositions were performed. In addition, deposit samples were collected at the same location for chemical analyses. This information characterized well the combustion environments adjacent to the superheaters and reheaters of utility boilers burning different U.S. coals. The gas and deposit compositions were then simulated in a series of 1000-hour laboratory corrosion tests in which the corrosion performances of different alloys were evaluated at 704oC (1300oF). Results of this laboratory study led to better understanding of the corrosion mechanisms operating on superheaters and reheaters in coal-fired boilers due to the mutual presence of sulfur and chlorine in coal. A new corrosion mechanism, i.e., “Active Sulfide-to-Oxide Corrosion Mechanism,” accounts for the rapid corrosion attack on low-alloy ferritic steels and lower-grade stainless steels resulting from the formation of iron chloride (FeCl2) vapor and associated cycling reactions. For higher alloys containing sufficient chromium, the attack is dominated by Hot Corrosion in the presence of a fused salt. In addition, two stages of the hot corrosion mechanism have been elucidated here in detail. The initiation of hot corrosion attack induced by molten sulfate may involve Stage 1 “acidic” fluxing and re-precipitation of the protective scale formed initially on the deposit-covered alloy surfaces, followed by Stage 2 Hot Corrosion dominated by “basic” fluxing and re-precipitation after the scale is locally penetrated by the fused salt.

High-Temperature Corrosion Mechanisms for Selected Iron and Nickel-Based Alloys Exposed to Sulfur and Chlorine-Containing Environments

Revealing the Effect of O2, SO2 and H2O in Supercritical CO2 on the Corrosion Behavior of 316L Steel at Elevated Temperature

High-temperature corrosion behaviours of nickel–iron-based alloys with different molybdenum and tungsten contents in a coal ash/flue gas environment

High Temperature Corrosion Resistance of Different Commercial Alloys Under Various Corrosive Environments

Effect of Alloying Chemistry on Fireside Corrosion Behavior of Ni–Fe-Based Superalloy for Ultra-supercritical Boiler Applications

Fireside Corrosion Behaviors of Super304H and HR3C in Coal Ash/Gas Environment with Different SO 2 Contents at 650 °C

Fireside Corrosion Behaviors Of Super304h And Hr3c In Coal Ash/Gas Environment With Different So2 Contents At 650 Degrees C

High-temperature corrosion of water-wall tubes in oxy-combustion atmosphere

High-Temperature Corrosion of Nickel-Based Coatings for Biomass Boilers in Chlorine-Containing Atmosphere

Chlorine-induced Gas-Solid coupled corrosion behaviors of tube materials in high steam parameter MSW incinerator

Hot corrosion behaviors of TP347H and HR3C stainless steel with KCl deposit in oxy-biomass combustion

Effect of Fouling Layer (Acid–Ash Reaction) on Low-Temperature Corrosion Covering Heating Surface in Coal-Fired Flue Gas

Study of Corrosion Kinetic Measurement and Morphology Observation of Superheater Tube 12cr1mov Alloy in Simulated MSWI Flue Gas Containing Varied HCl or SO2 Concentrations

Investigation of the Fireside Corrosion of a New Wrought Ni-Fe-Cr-based Alloy in Advanced Ultra-Supercritical Steam Boilers

High-Temperature Degradation and Protection of Ferritic and Austenitic Steels in Steam Generators

Water Wall Tubes’ High Temperature Corrosion Root Cause Investigation: A 300 MW Level Boiler Case

Pilot-scale corrosion tests of high chlorine coal using novel resistance probes

High‐temperature corrosion behaviors of typical nickel alloy coatings in a simulated boiler coal ash/gas environment in the Zhundong region

A Study of the Corrosion Behaviour of Magnetron-Sputter Deposited Coatings in a Reducing-Sulphidising Atmosphere at 600°C

High-temperature Corrosion Mechanism Analysis of 310S Alloy in Typical MSWI Flue Gas Environment at 460–580 °C