Abstract:Hot wire laser welding reduces the requirement of wire feeding accuracy and improves wire deposition efficiency with preheating wire by resistance heat. Due to merits like low heat input and high deposition rate, this method has broad potential applications like welding and additive manufacturing. It is a key problem to maintain stable wire transfer in hot wire laser welding since the preheated wire should be kept contacted with the work piece to maintain high temperature. A high-speed imaging system was used to observe wire transfer behaviors, which are divided into three types: fusing transfer, continuous transfer, and wire hit transfer. Only the continuous transfer is the stable wire transfer, which guarantees good weld formation. The wire transfer behavior is determined by wire temperature, and the temperature criterion of wire transfer is obtained by image analysis and temperature measurement. Two characteristic points P1 and P2 on the filler wire were found out, whose temperatures were used to judge wire transfer behaviors. The temperature criterion of the stable wire transfer is interpreted that the temperature of P1 (T P1) must be no more than the wire solidus and the temperature of P2 (T P2) must be no less than the wire liquidus. A heat conduction model of hot wire laser welding was established to calculate T P1 and T P2 for the used 308-L stainless wire. The welding parameters, which made up isothermal surfaces of T P1 = 1398 °C and T P2 = 1454 °C, respectively, the solidus and liquidus of the used wire, were obtained by iteration calculation of wire temperature. The parameters window of the stable wire transfer was located between the two isothermal surfaces. For the stable wire transfer in hot wire laser welding, the resistance heat of the wire cannot exceed the heat which fuses the wire tip outside the molten pool. Meanwhile, the total heat of the wire, including the resistance heat and the heat conducted from the molten pool, must exceed the heat which melts the wire tip inside the molten pool.

Study of metal transfer control in underwater wet FCAW using pulsed wire feed method

Current research status and prospect of metal transfer process control methods in gas metal arc welding

Control of Wire Transfer Behaviors in Hot Wire Laser Welding

Influence of calcium fluoride on underwater wet welding process stability

Effect of high-frequency phase shift on metal transfer and weld formation in aluminum alloy double-wire DP-GMAW

Effective Control Approach on Molten Droplet Size in Waveform Controlled Short Circuit Co2 Arc Welding

Operational performance and metal droplet formation in pulsed-shielded metal arc underwater welding

Investigation on droplet transfer behavior during fiber laser-flux cored arc hybrid welding

Simulation and control of metal droplet transfer in bypass coupling wire arc additive manufacturing

Probing Element Transfer Behavior during the Submerged Arc Welding Process for CaF2-SiO2-Na2O-Cr2O3 Agglomerated Fluxes: A Thermodynamic Approach

A Real-Time Monitoring Method for Droplet Transfer Frequency in Wire-Filled GTAW Based on Arc Sensing

Key mechanism of metal transfer and characteristic of cavity evolution during SAW using in-situ X-ray imaging method

Microstructure control of ultra-high-strength AlZnMgCu alloys fabricated by wire arc directed energy deposition: the role of variable polarity electric pulse

Effects of process parameters on the depth-to-width ratio of flux-cored wire underwater wet welding

Influence of Interwire Distance and Arc Length on Welding Process and Defect Formation Mechanism in Double-Wire Pulsed Narrow-Gap Gas Metal Arc Welding

EFFECTS OF HEAT INPUT ON THE MICROSTRUC-TURE AND IMPACT TOUGHNESS OF WELD METAL PROCESSED BY A NEW FLUXNOVEL FLUX CORED WIRE WELD

Double-Pulse Triple-Wire MIG Welding of 6082-T6 Aluminum Alloy: Process Characteristics and Joint Performances

Study on Arc Behavior and Weld Formation of Magnetically Controlled Narrow Gap TIG Welding

Dynamic Metal Transfer Behavior in Double-Wire DP-GMAW of Aluminum Alloy Under Different Pulse Phases

Comparative Study of Droplet Transfer Modes on Appearance, Microstructure, and Mechanical Properties of Weld During Pulsed GMAW

Heat input characteristics and weld bead formation in double-wire double-pulsed GMAW of aluminum alloy under different low-frequency phases