Abstract:Printing of electrical circuits and interconnects using isotropic conductive adhesives (ICAs) is of great interest due to their low-temperature processing and compatibility with substrates for applications in sensors, healthcare, and flexible devices. As a lower cost alternative to silver (Ag), copper (Cu)-filled ICAs are desirable but limited by the formation of high-resistivity Cu surface oxides. To overcome this limitation, self-assembled monolayers (SAMs) of octadecanethiol (ODT) have been demonstrated to reduce the oxidation of micrometer-scale Cu powder particles for use in ICAs. However, the deposition and function of the SAM require further investigation, as described in this paper. As part of this work, the stages of the SAM deposition process, which included etching with hydrochloric acid to remove pre-existing oxides, were studied using X-ray photoelectron spectroscopy (XPS), which showed low levels of subsequent Cu oxidation when ODT coated. The treated Cu powders were combined with one- or two-part epoxy resins to make Cu-ICAs, and the effect of the Cu surface condition and weight loading on electrical conductivity was examined. When thermally cured in an inert argon atmosphere, ICAs filled with Cu protected by ODT achieved electrical conductivity up to 20 × 105 S·m-1, comparable to Ag-ICAs, and were used to make a functional circuit. To understand the function of the SAM in these Cu-ICAs, scanning and transmission electron microscopy were used to examine the internal micro- and nano-structures along with the elemental distribution at the interfaces within sections taken from cured samples. Sulfur (S), indicative of the ODT, was still detected at the internal polymer-metal interface after curing, and particle-to-particle contacts were also examined. XPS also identified S on the surface of cured Cu-ICAs even after thermal treatment. Based on the observations, electrical contact and conduction mechanisms for these Cu-filled ICAs are proposed and discussed.

Incorporation of Tin on Copper Clad Laminate to Increase the Interface Adhesion for Signal Loss Reduction of High-Frequency PCB Lamination

Adhesion improvement of Cu-based substrate and epoxy molding compound interface by hierarchical structure preparation

Effect of High-Frequency and High-Density Current on Adhesive Strength of Copper Thin Film

Strong Adhesion of Electroless Plated Copper by Optimizing Lamination Temperature of Epoxy Composite Film for Advanced Chip Packaging Substrates

Metallized Liquid Crystal Polymer with Low Interfacial Roughness and Excellent Adhesive Strength Based on Semi-Additive Process for High-Frequency Signal Transmission

Copper conductive adhesives for printed circuit interconnects

Trace Bis-(3-sulfopropyl)-disulfide Enhanced Electrodeposited Copper Foils

Whisker inhibited Sn–Bi alloy coating on copper surface to increase copper bonding strength for signal loss reduction of PCB in high-frequency

Surface Graft Copolymerization Enhanced Adhesion of an Epoxy-Based Printed Circuit Board Substrate (Fr-4) to Copper

Pull-off Testing and Electrical Conductivity of Sn-Based Metal Powder Mixtures Cold Sprayed on Carbon Fiber-Reinforced Polymers

Adhesion improvement of sputtered Cu films on flexible polymer substrates through the design of metal interlayers

Fabrication of Sn-plated Cu foam for high-efficiency transient-liquid-phase bonding

Elimination of Pores in Ag–Sn TLP Bonds by the Introduction of Dissimilar Intermetallic Phases

The Role of Self-Assembled Monolayers in the Surface Modification and Interfacial Contact of Copper Fillers in Electrically Conductive Adhesives

Improvement of the Adhesion and Diamond Content of Electrodeposited Cu/Microdiamond Composite Coatings by a Plated Cu Interlayer

Grafting Amino Groups onto Polyimide Films in Flexible Copper-Clad Laminates Using Helicon Plasma

Study of Surface Treatment of Copper Fillers for Improvement of Electrically Conductive Adhesives

Effect of Sn Plating Thickness on Wettability, Solderability, and Electrical Connections of Electronic Lead Connectors for Surface Mount Technology Applications

Microstructural Characteristics of Immersion Tin Coatings on Copper Circuitries in Circuit Boards

A New Method to Obtain Cu Films with Lower Resistivity and Higher Interface Adhesion on Different Substrates

Metallization of a LTCC substrate by electroless copper plating