Abstract:This study aimed to enhance the sinterability and conductivity of yttria fully stabilized zirconia electrolyte through co-doping by 2 mol% of ZnO and different contents of MnO 2 (0, 0.5, 1, 1.5 mol%) at two sintering temperatures of 1300 and 1400 °C. Phase composition identification, density, microstructure, and conductivity of the samples were evaluated using X-ray diffraction (XRD), Archimedes' method, field emission scanning electron microscopy (FESEM), and electrochemical impedance spectroscopy (EIS), respectively. The XRD results revealed that ZnO and MnO 2 are successfully doped in the fluorite structure of YSZ sintered at 1400 °C, and the cubic structure is completely preserved. However, at a sintering temperature of 1300 °C, the (111) peaks of doped samples were slightly split, which implied a slight phase transformation of YSZ from cubic to a tetragonal structure. The co-doped samples, at both sintering temperatures, showed higher relative density and grain size compared with pure YSZ. The addition of 2 mol% of ZnO and 0.5 mol% of MnO 2 at 1400 °C increased the relative density of YSZ from 81.6% to 95.1%. The increase in relative density and grain size, while maintaining the cubic structure, caused an increase in the conductivity of the mentioned sample. Compared with pure YSZ, the sample's total conductivity increased from 7.37 to 10.03 S m −1 at 800 °C. The proposed composition showed better sintering behavior, lower activation energy of grain conductivity, and higher conductivity than pure YSZ. This behavior is thought to be due to the facilitating rearrangement of atoms during sintering and an increase in oxygen ion vacancy concentration due to co-doping with the appropriate amount of ZnO and MnO 2 .

Comparative Study of the Sintering Behaviors Between YSZ and LZ/YSZ Composite

Cubic Yttria Stabilized Zirconia Sintering Additive Impacts: A Comparative Study

The Effect of Sintering Temperature on the Microstructure and Phase Transformation in Tetragonal YSZ and LZ/YSZ Composites

Improved Mechanical Properties of 3YSZ Ceramics Prepared by Pressure-less Sintering Assisted by Cold Sintering under Mild Conditions

Diffusion Mechanism of Oxygen Ions in La2Zr2O7/YSZ Composite Ceramics

Sintering resistance of La2Ce2O7, La2Zr2O7, and yttria stabilized zirconia ceramics

Effects of ZnO Sintering Additive on the Sintering Behavior and Conductivity of YSZ Solid Electrolyte

Mechanical and electrical properties of 3Y‐TZP/TiSi2 composites sintered at different temperatures

The Properties of YSZ Electrolyte Sintering at 1300 °C

Chemical Compatibility Between Ln2Zr2O7 (ln = Nd, Sm, Gd) and Tetragonal Yttria Stabilized Zirconia after Annealing at High Temperatures

Effect Of Sio2 Content On Sintering Characteristics Of Ysz In High Temperature Aging

Influence of Powder States on the Composition and Phase Stability of LZ/YSZ Composite Thermal Barrier Coatings

The Propertied Of Ysz Electrolyte Sintering At 1300 Degrees Enc

Low-Cost Preparation of YSZ-SiC High-Temperature Composite from Zircon and Y2O3 by Carbothermal Reduction

Effect of Li2o Additions Upon the Crystal Structure, Sinterability and Electrical Properties of Yttria Stabilized Zirconia Electrolyte

Hot-pressed ZrB2–SiC–YSZ Composites with Various Yttria Content: Microstructure and Mechanical Properties

Sintering and Electrical Properties of YSZ Electrolyte Tubes with Thin Wall Prepared by an Improved Slip Casting

Enhancing sintering behavior and conductivity of YSZ electrolyte by co-doping of ZnO and MnO 2

Effect of YSZ Composite Ceramics with Different LaF3 Doping Content on Microstructure Evolution and Infrared Emissivity

Physical characterization of composites based on yttria‐stabilized zirconia and doped lanthanum gallate

Sintering mechanisms of partially stabilized zirconia (TZ3Y) with ZnO and Co3O4 as sintering additives