Abstract:Objectives To investigate transient thermal stresses that developed in 3Y-TZP green compacts during speed sintering. Methods A total of 312 disc-shaped green compacts (Ø17.1 ×1, 1.5, 2, 2.5, 3 mm) were cold-isostatically pressed from 3Y-TZP powder (Zpex, Tosoh Corp.) for speed sintering studies as well as compositional analysis and biaxial flexural strength measurements (both at room temperature and following heating at 90 °C/min to 500 °C). Flexural strength was determined using the piston-on-3-ball method. Phase assemblies were analyzed using the X-ray diffraction method. Effects of heating/cooling rates on transient stresses were investigated by conducting definitive sintering studies to determine the threshold for fracture. Finite element analysis (FEA) was used to validate the experimental findings using measured thermomechanical properties. Results The bulk and relative density of the green compact were 2.95 ± 0.03 g/cm 3 and 48.52% ± 0.45%. The flexural strength was drastically decreased from 10.3 ± 0.4 MPa to 1.09 ± 0.07 MPa following heating at 90 °C/min to 500 °C. The monoclinic and tetragonal contents were 54.9% and 45.1%, respectively. The threshold for fracture was located at 500 °C during the first heating stage with a 90 °C/min heating rate in specimens of 2.5 mm thickness or greater. No fractures occurred in the second heating stage and cooling phase. The FEA estimated that the principal transient tensile stress was ∼1.14 MPa at 500 °C during the heating phase, which exceeded the corresponding flexural strength (1.09 ± 0.07 MPa). Significance Advanced FEA methods are an accurate and efficient tool to analyze the history of transient stresses during sintering of ceramic dental restorations.

The Effect of Sintering Temperature on the Microstructure and Phase Transformation in Tetragonal YSZ and LZ/YSZ Composites

Cubic Yttria Stabilized Zirconia Sintering Additive Impacts: A Comparative Study

Comparative Study of the Sintering Behaviors Between YSZ and LZ/YSZ Composite

Effect of Sintering Time on the Stability of Y2O3 Partially Stabilized Zirconia

Effect of Sintering Temperature on Compressive Strength of Porous Yttria-Stabilized Zirconia Ceramics

Phase Transition Behavior of Yttria-Stabilized Zirconia from Tetragonal to Monoclinic in the Lanthanum Zirconate/yttria-Stabilized Zirconia Coupled-System Using Molecular Dynamics Simulation

Influence of Powder States on the Composition and Phase Stability of LZ/YSZ Composite Thermal Barrier Coatings

Hot-pressed ZrB2–SiC–YSZ Composites with Various Yttria Content: Microstructure and Mechanical Properties

Thermophysical and mechanical properties of cubic, tetragonal and monoclinic ZrO2

Physical characterization of composites based on yttria‐stabilized zirconia and doped lanthanum gallate

Diffusion Mechanism of Oxygen Ions in La2Zr2O7/YSZ Composite Ceramics

Low-Cost Preparation of YSZ-SiC High-Temperature Composite from Zircon and Y2O3 by Carbothermal Reduction

In-situ high temperature micromechanical testing of ultrafine grained yttria-stabilized zirconia processed by spark plasma sintering

Effect of thermal treatment at high temperature on phase stability and transformation of Yb2O3 and Y2O3 co-doped ZrO2 ceramics

High Temperature Mechanical Properties of Zirconia Metastable T '-Phase Degraded Yttria Stabilized Zirconia

Mechanical and electrical properties of 3Y‐TZP/TiSi2 composites sintered at different temperatures

Transient thermal stresses developed during speed sintering of 3 mol% yttria-stabilized tetragonal zirconia polycrystals

Chemical Compatibility Between Ln2Zr2O7 (ln = Nd, Sm, Gd) and Tetragonal Yttria Stabilized Zirconia after Annealing at High Temperatures

Critical effect of cubic phase on aging in 3 mol% yttria-stabilized zirconia ceramics for hip replacement prosthesis

Raman and X-ray photoelectron spectroscopic characterizations of thermal stability of 3 mol% yttria stabilized zirconia ceramics

Microstructural dependence of aging induced phase transformation in Y2O3 partially stabilized ZrO2 polycrystals