An Integrated Mode (de)multiplexer Based on Adiabatic Couplers

Chunlei Sun,Yu,Mengyuan Ye,Lei Shi,Xinliang Zhang

DOI: https://doi.org/10.1364/cleo_si.2016.sm1f.7

2016-01-01

Abstract:A novel broadband mode-division multiplexing link based on adiabatic couplers is proposed and experimentally demonstrated with crosstalk < -20 dB, insertion loss < 1 dB and power penalty < 1 dB, using Silicon integrated platform.

What problem does this paper attempt to address?

Design and Numerical Optimization of A Mode Multiplexer Based on Few-Mode Fiber Couplers

Yiwei Xie,Songnian Fu,Hai Liu,Hailiang Zhang,Ming Tang,P. Shum,Deming Liu

DOI: https://doi.org/10.1088/2040-8978/15/12/125404

IF: 2.1

2013-01-01

Journal of Optics

Abstract:Mode division multiplexing (MDM) transmission based on few-mode fibers (FMFs) appears to be an alternative solution for overcoming the capacity limit of single-mode fibers (SMFs). A FMF coupler-based mode division multiplexer/demultiplexer (MMUX/DeMMUX) is proposed and theoretically investigated after the fabricated FMF is characterized. MMUXs/DeMMUXs with a mode contrast ratio (MCR) of more than 20 dB can be obtained for two-mode multiplexing and three-mode multiplexing over a wavelength span of 60 and 10 nm, respectively. We numerically verify the proposed MMUX/DeMMUX which has the advantages of high MCR, easy fabrication and maintenance, and low wavelength dependence.
Mode Multiplexers With Tapers Based On Shortcuts To Adiabaticity

Defen Guo,Yejin Zhang,Tao Chu

DOI: https://doi.org/10.1109/CLEOPR.2017.8118927

2017-01-01

Abstract:Broadband, low-loss and low-crosstalk silicon mode (de) multiplexers with optimized tapers based on shortcuts to adiabaticity (STA) are proposed and experimentally demonstrated. The measured insertion losses and crosstalks are less than 1.1 dB and -24 dB, respectively, for the five two-mode mode-division-multiplexing (MDM) links over wavelengths ranging from 1500 nm to 1600 nm. The four-mode MDM link showed measured insertion losses and crosstalks less than 1.3 dB and -23 dB, respectively, within the same wavelength range. The method paves the way for future adaptation of the STA protocols to various components.
Silicon Mode (de)multiplexers with Parameters Optimized Using Shortcuts to Adiabaticity.

Defen Guo,Tao Chu

DOI: https://doi.org/10.1364/oe.25.009160

IF: 3.8

2017-01-01

Optics Express

Abstract:We propose and experimentally demonstrate broadband silicon mode (de)multiplexers based on the optimization of system adiabaticity using shortcuts to adiabaticity (STA). The measured insertion losses and crosstalks were less than 1.1 dB and -24 dB, respectively, for the five two-mode mode-division-multiplexing (MDM) links over wavelengths ranging from 1500 nm to 1600 nm. The four-mode MDM link showed measured insertion losses and crosstalks less than 1.3 dB and -23 dB, respectively, within the same wavelength range. The method paves the way for future adaptation of the STA protocols to various components.
Design of an Ultra-Broadband Silicon Mode (De)multiplexer

Weiwei Chen,Pengjun Wang,Yawei Zhang,Jianyi Yang

DOI: https://doi.org/10.1016/j.optcom.2015.10.066

IF: 2.4

2016-01-01

Optics Communications

Abstract:We propose a low-crosstalk and broadband mode (de)multiplexer. It is designed by cascading mode (de)interleavers utilizing silicon waveguide asymmetric Y-junctions. Asymmetric Y-junctions of each stage are modular. For each asymmetric Y-junction, the even (odd) modes of the stem separated from the odd (even) modes evolve into the low-order modes of the wide (narrow) arm by controlling the widths of the two arms, and vice versa. A four-channel mode (de)multiplexer for TE polarization is analyzed as an example. Simulations show the four-channel mode (de)multiplexer pair has a low crosstalk (<−14.1dB) over a common spectral bandwidth of 280nm.
Ultra-compact Silicon Mode (de)multiplexer Based on Directional Couplers with Subwavelength Sidewall Corrugations

Xiaofei Wang,Nannan Ning,Hui Yu,Yuehai Wang,Jianyi Yang

DOI: https://doi.org/10.1364/ol.449493

2021-01-01

Abstract:Asymmetrical directional couplers aided with subwavelength sidewall corrugations are used to realize ultra-compact silicon mode (de)multiplexers at C-band. Three mode (de)multiplexers with ultra-short coupling lengths of 5.6/6.5/7.7 μm are designed to enable low-loss mode conversions between TE0 and TE1/2/3 modes. They are then cascaded to build a four-channel mode-division-multiplexing (MDM) link. The four mode channels present minimal on-chip insertion losses of 0.2/0.7/0.7/0.9 dB at their peak wavelengths. Measured cross talk levels of the four mode channels are better than -18.0/-19.1/-16.0/-18.2 dB within the wavelength range from 1530 nm to 1580 nm.
Experimental Demonstration of a Broadband Two-Mode Multi/demultiplexer Based on Asymmetric Y-junctions

Haiqin Li,Pengjun Wang,Tianjun Yang,Tingge Dai,Gencheng Wang,Shiqi Li,Weiwei Chen,Jianyi Yang

DOI: https://doi.org/10.1016/j.optlastec.2017.09.043

2018-01-01

Abstract:A broadband two-mode multi/demultiplexer using asymmetric Y-junctions is designed and experimentally demonstrated on a silicon-on-insulator platform for on-chip mode-division multiplexing applications. Within a bandwidth from 1513 to 1619 nm, the fabricated device, which consists of a two-mode multiplexer, a multimode straight waveguide, and a two-mode demultiplexer, exhibits demultiplexing crosstalk of less than -9.1 dB. The demultiplexing crosstalk as low as -42.1 dB, lower than -12.8 dB over the C band can be obtained. The measured insertion loss varies from 0.40 to 0.56 dB at a wavelength of 1550 nm. A transmission experiment of 10 Gbit/s electrical signals carried on TE0 and TE1 modes is successfully achieved with open and clear eye diagrams. (C) 2017 Elsevier Ltd. All rights reserved.
Ultra-broadband and low-modal-crosstalk mode multiplexer based on cascaded vertical directional couplers formed by adiabatic-tapered waveguides without mode conversion

Quandong Huang,Jiafeng He,Zhaoqiang Zheng,Xinyu Zhou

DOI: https://doi.org/10.1109/jlt.2023.3322638

IF: 4.7

2023-01-01

Journal of Lightwave Technology

Abstract:We present an ultra-broadband and low-modal-crosstalk mode multiplexer based on cascaded vertical directional couplers formed by adiabatic-tapered waveguides without mode conversion. The input and output ports of the mode multiplexer are designed in the same planar layer to meet the standard package requirement. We design and fabricate a three-mode mode multiplexer, which serves to spatially combine and separate the E11, E21 and E12 modes in the few-mode-core outputs without mode conversion with polymer material, where adiabatic tapers are utilized in the design of directional coupler to extend the operation wavelength and two pairs of directional couplers serve to suppress the modal crosstalks. We fabricate a typical device to demonstrate the idea. The fabricated device has a length of 29 mm, which provides coupling ratios higher than 97% and modal crosstalks lower than – 19.6 dB over the C+L band and beyond with weak polarization dependence. The proposed mode multiplexer is fiber capable and allows to connect with the few-mode fibers directly by the use of fan-in and fan-out technology. The proposed mode multiplexer is simple, scalable, and effective to extend the operation wavelength as well as suppressing the modal crosstalks, which provides a powerful device to manipulate the modes in a mode division multiplexing system and an effective method to realize an all-optical chip for simplifying the Multi-Input Multi-Output signal processing with low power consumption.

engineering, electrical & electronic,optics,telecommunications
Silicon-on-Insulator Mode (de)multiplexer for On-Chip Mode-Division Multiplexing

Huiye Qiu,Hui Yu,Yongheng Jin,Yuehai Wang,Xiaoqing Jiang

DOI: https://doi.org/10.1364/acp.2013.af1a.2

2013-01-01

Abstract:We propose a simple 1×4 silicon mode (de)multiplexer based on multimode grating-assisted-couplers. Due to the contra-directional coupling, precise control of the coupling strength and the coupling length are not needed.
Low-Crosstalk and Low-Loss Mode (de)Multiplexer with 10 Channels

Chenlei Li,Hao Wu,Daoxin Dai

DOI: https://doi.org/10.1364/acpc.2017.m2d.3

2017-01-01

Abstract:A 10-channel mode (de)multiplexer with low crosstalks and low loss over a broad wavelength band is proposed and realized with cascaded dual-core adiabatic tapers on a silicon-on-insulator (SOI) platform for the first time.
Mode Multi/demultiplexer Based on Cascaded Asymmetric Y-junctions

Weiwei Chen,Pengjun Wang,Jianyi Yang

DOI: https://doi.org/10.1364/oe.21.025113

IF: 3.8

2013-01-01

Optics Express

Abstract:A mode-(de)multiplexer with low loss and large spectral bandwidth is proposed. The device is designed by utilizing a structure with cascaded asymmetric Y-junctions. By carefully controlling the widths of the wide and narrow arms of the Y-junctions, the fundamental mode of a narrow arm excites the higher-order mode of its stem in the multiplexing case, and a high-order mode of the stem separated from other lower-order modes evolves into the fundamental mode of the narrow arm in the demultiplexing case. As an example, a 1 × 4 mode-(de)multiplexer is analyzed by using the beam propagation method. Simulation results show the demultiplexed crosstalk is lower than -21.8 dB, under a common spectral bandwidth of 140 nm. The insertion loss is negligible.
Three-mode All-Optical (de)multiplexing on a SOI Chip

Yan-Si Le,Zhi Wang,Zhi-Yong Li,Ying Li,Qiang Li,Can Cui,Chong-Qing Wu

DOI: https://doi.org/10.1016/j.optcom.2017.04.059

IF: 2.4

2018-01-01

Optics Communications

Abstract:An on-chip three-mode division multiplexing circuit using a simple ADC-based TE 0 & TE 1 & TE 2 (de)multiplexer is demonstrated to improve the link capacity of on-chip optical interconnects. The proposed (de)multiplexer does not contain any tapered waveguide which is different from the previous mode (de)multiplexer based on ADCs. Here, we choose multimode waveguide width first and then confirm corresponding width of the other two waveguides. Thus the bus waveguide without any tapers can not only reduce complexity of (de)multiplexer but also reduce difficulty of the fabrication. Our simulation results show that the hybrid multiplexer has relatively low loss and low crosstalk about −40 dB, −26.99 dB and −28.72 dB for each mode around 1550 nm with a width-variation w =±25 nm. These properties make the proposed mode-(de)multiplexer suitable for application in high-capacity data transmission.
Silicon Mode Multi/Demultiplexer Based on Multimode Grating-Assisted Couplers

Huiye Qiu,Hui Yu,Ting Hu,Guomin Jiang,Haifeng Shao,Ping Yu,Jianyi Yang,Xiaoqing Jiang

DOI: https://doi.org/10.1364/oe.21.017904

IF: 3.8

2013-01-01

Optics Express

Abstract:A simple and low-crosstalk 1 × 4 silicon mode (de)multiplexer based on multimode grating-assisted-couplers is proposed. Mode transitions can be flexibly controlled by designing the grating period at the phase-matching condition. Due to the contra-directional coupling, precise control of the coupling strength and the coupling length are not needed in the system. Calculation results show that the insertion loss and the 3 dB bandwidths of the device are 0.2 dB and 3.7 nm, 0.34 dB and 7.6 nm, and 0.21 dB and 11.8 nm for the channels which (de)multiplex to the 1st, 2nd, and 3rd modes of the bus waveguide, respectively.
Silicon Mode (de)multiplexer Based on Cascaded Particle-Swarm-Optimized Counter-Tapered Couplers

Weiwei Chen,Hongxiang Li,Bohao Zhang,Pengjun Wang,Shixun Dai,Yuxiao Liu,Jun Li,Yan Li,Qiang Fu,Tingge Dai,Hui Yu,Jianyi Yang

DOI: https://doi.org/10.1109/jphot.2020.3046361

IF: 2.4

2020-01-01

IEEE Photonics Journal

Abstract:In this paper, a design of a silicon mode (de)multiplexer based on cascaded counter-tapered couplers is proposed and investigated. By using the particle swarm optimization algorithm and finite difference time domain method, structural parameters of each counter-tapered coupler in our proposed mode (de)multiplexer are optimized so that high conversion efficiencies can be obtained and coupling lengths can be significantly shortened. The coupling lengths of counter-tapered couplers in the proposed silicon four-mode (de)multiplexer operating in transverse-electric polarization are 8 μm, 9 μm, and 10 μm. The corresponding conversion efficiencies are respectively 98.98%, 99.98%, and 98.68%. Experimental results show that, the fabricated device exhibits a demultiplexed crosstalk of -32.76 dB, -27.10 dB, -32.45 dB, or -33.29 dB at 1550 nm wavelength, when the fundamental transverse-electric mode is respectively launched into the ports Input0, Input1, Input2, or Input3. The measured demultiplexed crosstalk is less than -15.15 dB from 1525 to 1596 nm and lower than -18.12 dB from 1525 to 1561 nm.
Silicon Two-Mode Multi/demultiplexer Based on Tapered Couplers

Haiqin Li,Shiqi Li,Tianjun Yang,Jiayun Xu,Jun Li,Weiwei Chen,Pengjun Wang,Tingge Dai,Gencheng Wang,Jianyi Yang

DOI: https://doi.org/10.1016/j.ijleo.2018.09.115

IF: 3.1

2018-01-01

Optik

Abstract:In this paper, a two-mode (de)multiplexer utilizing the coupling between tapered waveguides and a wide multimode waveguide is designed and experimentally demonstrated. The tapered waveguides are composed of a reverse-tapered waveguide and a narrow tapered waveguide. The proposed mode (de)multiplexer is fabricated on silicon-on-insulator (SOI) wafer in a commercial 0.18-mu m CMOS-compatible process. The qualitative functionality of the device is mainly determined by the width of the large end of the reverse-tapered waveguide. Experimental results show that the demultiplexing crosstalk of a pair of tapered-coupler-based two-mode (de)multiplexers is lower than -13.5 dB within a bandwidth from 1528 nm to 1570 nm and less than -16.6 dB from 1540 nm to 1560 nm.
Low-loss and Low-Crosstalk Multi-Channel Mode (de)multiplexer with Ultrathin Silicon Waveguides

Chenlei Li,Daoxin Dai

DOI: https://doi.org/10.1364/ol.42.002370

2017-01-01

Abstract:A multi-channel mode (de) multiplexer based on the super-mode evolution in cascaded dual-core adiabatic tapers is designed and realized with ultrathin (similar to 50 nm) siliconon-insulator nanowire waveguides. This dual-core adiabatic taper is designed optimally, so that all the supermodes are confined in the wide core at the input end and the highest-order supermode is localized in the narrow core at the output end. In this way, the highest-order supermode is dropped as the fundamental mode at the cross port. As an example, a (de) multiplexer with three mode channels is designed and fabricated. From the measured spectral responses, the fabricated device has a crosstalk lower than -20 dB and an excess loss less than 0.2 dB in a bandwidth of similar to 65 nm. (C) 2017 Optical Society of America
Compact broadband silicon 3 dB coupler based on shortcuts to adiabaticity.

Defen Guo,Tao Chu

DOI: https://doi.org/10.1364/OL.43.004795

IF: 3.6

2018-01-01

Optics Letters

Abstract:We proposed and experimentally demonstrated a compact, broadband, and low-loss-mode-evolution-based 2 x 23 dB coupler on a silicon-on-insulator platform. The waveguide widths and separations of the coupler were tapered in an optimal manner using the shortcuts to the adiabaticity method. The coupler, with a similar to 70 mu m total length and 200 nm feature size, exhibited <0.3 dB measured excess loss over a broadband wavelength range from 1500 to 1600 nm. Balanced and unbalanced Mach-Zehnder interferometers fabricated for validation showed extinction ratios larger than 27 and 23 dB, respectively, over a 100 nm bandwidth. The extracted splitting ratio was between 0.48 and 0.52. (C) 2018 Optical Society of America
Broadband Nine-Channel Mode-Division (de)multiplexer Based on Densely Packed Multimode Waveguide Arrays

Hongnan Xu,Yaocheng Shi

DOI: https://doi.org/10.1109/jlt.2017.2763970

IF: 4.7

2017-01-01

Journal of Lightwave Technology

Abstract:A compact and broadband nine-channel modedivision (de) multiplexer is proposed and demonstrated. The asymmetrical directional coupler based multimode (de) multiplexers and the densely packed multimode waveguide arrays are combined to enhance the mode capacity. The proposed (de) multiplexer shows theoretical crosstalk that is < -15 dB over an 100-nm wavelength band for all the nine channels. The experimental results show a low crosstalk that is < -15 dB over a 55-nm wavelength range for all the supported modes.
Silicon Three-Mode (de)multiplexer Based on Cascaded Asymmetric Y Junctions.

Weiwei Chen,Pengjun Wang,Tianjun Yang,Gencheng Wang,Tingge Dai,Yawei Zhang,Liqiang Zhou,Xiaoqing Jiang,Jianyi Yang

DOI: https://doi.org/10.1364/ol.41.002851

IF: 3.6

2016-01-01

Optics Letters

Abstract:A three-mode (de)multiplexer based on two cascaded asymmetric Y junctions is proposed and experimentally demonstrated on a silicon-on-insulator platform for mode-division multiplexing applications. Within a bandwidth from 1537 to 1566 nm, the best demultiplexing crosstalk of the fabricated device, composed of a three-mode multiplexer, a multimode straight waveguide, and a three-mode demultiplexer, is up to -31.5 dB, while in the worst case it is -9.7 dB. The measured maximum insertion loss is about 5.7 dB at a wavelength of 1550 nm. The mode crosstalk and insertion loss can be further improved by high-quality fabrication processes. (C) 2016 Optical Society of America
Mid-Infrared, Ultra-Broadband, Low-Loss, Compact Arbitrary Power Splitter Based on Adiabatic Mode Evolution

Jia Xu Brian Sia,Wanjun Wang,Xin Guo,Jin Zhou,Zecen Zhang,Mohamed Said Rouifed,Xiang Li,Zhong Liang Qiao,Chong Yang Liu,Callum Littlejohns,Graham T. Reed,Hong Wang

DOI: https://doi.org/10.1109/jphot.2019.2907788

IF: 2.4

2019-01-01

IEEE Photonics Journal

Abstract:We designed and demonstrated TE-mode arbitrary power splitters based on adiabatic mode evolution. The power splitters are designed with a footprint of smaller than 12 × 2.9 μm2, fabricated on a 400-nm silicon-on-insulator platform, requiring only a single etch step. The optimization process and the conditions for arbitrary-power splitting are performed using three-dimensional-FDTD simulations. We prove this concept through the fabrication of asymmetrical adiabatic evolution-based power splitters with splitting ratios of 50:50, 60:40, and 70:30. The fabricated devices are shown to agree closely with simulation results. Broadband operation with low insertion loss of 0.11–0.6 dB is demonstrated across the 3.66–3.89 μm wavelength range (230 nm). This component has applications in a multitude of areas such as spectroscopic optical sensing and optical phased arrays photonic integrated circuits etc.
Broadband dual-mode 2 x 2 3 dB multimode interference couplers with a shallowly etched multimode section

Chaochao Ye,Ming Zhang,Yaocheng Shi,Daoxin Dai

DOI: https://doi.org/10.1364/AO.397676

IF: 1.9

2020-01-01

Applied Optics

Abstract:A broadband dual-mode 2 x 2 3 dB power splitter on silicon is proposed by utilizing multimode interference (MMI) couplers with a shallowly etched multimode region. The present MMI coupler is designed optimally to be with reduced phase errors for all the excited higher-order modes in the MMI region by engineering the refractive-index profile with the assistance of a shallowly etched multimode region. Simulation results show the device works well for the TE0 and TE1 input modes over the C-band. For the TE0 input mode, the excess losses (ELs) and the imbalances (IBs) are, respectively, less than 0.4 and 0.12 dB in the wavelength range of 1.5-1.6 mu m, while the ELs and the IBs for the TE1 input mode are, respectively, less than 0.5 and 0.2 dB in the wavelength range of 1.53-1.58 mu m. Besides, the intermode cross-talk is less than -22 dB for TE0 and TE1 modes in the wavelength range of 1.5-1.6 mu m. The proposed dual-mode MMI coupler can be extended for more than two input modes. (C) 2020 Optical Society of America

An Integrated Mode (de)multiplexer Based on Adiabatic Couplers

Design and Numerical Optimization of A Mode Multiplexer Based on Few-Mode Fiber Couplers

Mode Multiplexers With Tapers Based On Shortcuts To Adiabaticity

Silicon Mode (de)multiplexers with Parameters Optimized Using Shortcuts to Adiabaticity.

Design of an Ultra-Broadband Silicon Mode (De)multiplexer

Ultra-compact Silicon Mode (de)multiplexer Based on Directional Couplers with Subwavelength Sidewall Corrugations

Experimental Demonstration of a Broadband Two-Mode Multi/demultiplexer Based on Asymmetric Y-junctions

Ultra-broadband and low-modal-crosstalk mode multiplexer based on cascaded vertical directional couplers formed by adiabatic-tapered waveguides without mode conversion

Silicon-on-Insulator Mode (de)multiplexer for On-Chip Mode-Division Multiplexing

Low-Crosstalk and Low-Loss Mode (de)Multiplexer with 10 Channels

Mode Multi/demultiplexer Based on Cascaded Asymmetric Y-junctions

Three-mode All-Optical (de)multiplexing on a SOI Chip

Silicon Mode Multi/Demultiplexer Based on Multimode Grating-Assisted Couplers

Silicon Mode (de)multiplexer Based on Cascaded Particle-Swarm-Optimized Counter-Tapered Couplers

Silicon Two-Mode Multi/demultiplexer Based on Tapered Couplers

Low-loss and Low-Crosstalk Multi-Channel Mode (de)multiplexer with Ultrathin Silicon Waveguides

Compact broadband silicon 3 dB coupler based on shortcuts to adiabaticity.

Broadband Nine-Channel Mode-Division (de)multiplexer Based on Densely Packed Multimode Waveguide Arrays

Silicon Three-Mode (de)multiplexer Based on Cascaded Asymmetric Y Junctions.

Mid-Infrared, Ultra-Broadband, Low-Loss, Compact Arbitrary Power Splitter Based on Adiabatic Mode Evolution

Broadband dual-mode 2 x 2 3 dB multimode interference couplers with a shallowly etched multimode section