Abstract:Cu2ZnSn(S, Se)4 (CZTSSe) is one of most competitive photovoltaic materials for its earth-abundant reserves, environmental friendliness, and high stability.The quality of CZTSSe absorber determines the power-conversion efficiency (PCE) of CZTSSe solar cells. The absorber's quality lies on post-selenization process, which is the reaction of Cu-Zn-Sn precursor and selenium vapor. And the post-selenization is dependent on various factors (e.g. temperature, precursor composition, reaction atmosphere, etc).However, synergistic regulation of these factors cannot be realized under a widely-used single-temperature zone selenization condition.Here, in our dual-temperature zone selenization scheme, a solid-liquid and solid-gas (solid precursor and liquid/gas phase Se) synergistic reaction strategy has been developed to precisely regulate the selenization. Pre-deposited excess liquid Se provides high Se chemical potential to drive a direct and fast formation of the CZTSSe phase, significantly reducing the amount of binary and ternary compounds within phase evolution. And organics removal can be accomplished via a synergistic optimization of Se condensation and subsequent volatilization. We achieve a high-performance CZTSSe solar cell with a remarkable PCE of 13.6%, and the highest large-area PCE of 12.0% (over 1cm2). Our strategy will provide a new idea for further improving efficiency of CZTSSe solar cells via phase evolution regulation, and also for other complicated multi-compound synthesis.

Fabrication of Cu2ZnSn(S,Se)4 thin film solar cells by selenization of reactively sputtered precursors

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Achieving 11.95% Efficient Cu2ZnSnSe4 Solar Cells Fabricated by Sputtering a Cu-Zn-Sn-Se Quaternary Compound Target with a Selenization Process

Preparing Cu2ZnSnSe4 thin film solar cells based on selenium containing precursors

Uniform monolayer Cu2ZnSn(S,Se)4 film based on novel precursor solution

Thin-Film Solar Cells Based on Selenized CuSbS2 Absorber

Optimum precursor stacking sequence of Cu2ZnSnSe4 thin film solar cell in selenium atmosphere

CZTSe solar cells prepared by electrodeposition of Cu/Sn/Zn stack layer followed by selenization at low Se pressure

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Cu2ZnSnSSe4 Solar Cells with 9.6% Efficiency Via Selenizing Cu-Zn-Sn-S Precursor Sputtered from a Quaternary Target

Using Cu–Zn–Sn–O Precursor to Optimize CZTSSe Thin Films Fabricated by Se Doping With CZTS Thin Films

Realization of 11.5% Efficiency Cu 2 ZnSn(S,Se) 4 Thin‐Film Solar Cells by Manipulating the Phase Structure of Precursor Films

Enhanced solar cell performance of Cu 2 ZnSnSe 4 thin films through structural control by using selenide stacked nanolayers in a non-toxic selenium atmosphere

An effective combination reaction involved with sputtered and selenized Sb precursors for efficient Sb2Se3 thin film solar cells

Cu2ZnSn(S, Se)4 solar cell with slight band tailing states achieves 11.83% efficiency by selenizing sputtered Cu–Zn–Sn–S precursor

A promising photovoltaic material Cu2MnSn(S,Se)4: Film growth and its application in solar cell

Controlling selenization equilibrium enables high-quality Cu2ZnSn(S, Se)4 absorbers for efficient solar cells

Fabrication of Cu2SnS3 Thin Film Solar Cells Via a Sol-Gel Technique in Air

10.24% Efficiency of Flexible Cu2 ZnSn(S,Se)4 Solar Cells by Pre-Evaporation Selenization Technique