Abstract:W-Y2O3 alloy with low DBTT (ductile-brittle transition temperature) and high RCT (recrystallization temperature), processed by high energy rate forging (HERF) was exposed to ITER-like steady-state and transient hydrogen plasma in the linear plasma generator Magnum-PSI. The steady-state heat fluxes were in the range of 8.35-16.32 MW center dot m(-2), resulting in surface base temperatures of the samples in the range of 1271 degrees C to 1982 degrees C. The applied transient peak heat flux with a frequency of 5 Hz (a total of 1000 pulses) was about 0.50 GW center dot m(-2). The exposure time was 220 s. No obvious morphological change of the exposed sample with a base temperature of 1271 degrees C was observed, except the preferential erosion of the W/Y2O3 interface. However, cracks along grain boundaries were formed on the surface of the exposed samples with base temperatures above 1389 degrees C. Pronounced recrystallization and grain growth also occurred for the samples with base temperatures of 1666 degrees C and 1982 degrees C. It is desirable to find that no wide and deep crack with preferential propagation direction with regard to the sample dimension was observed, even extensive recrystallization and cracking along grain boundaries occurred. This indicates that decreasing DBTT and increasing RCT simultaneously is desirable to broaden the safe operational temperature window of W as plasma-facing material, and therefore to increase the power handling capability of the plasma-facing units of a tungsten-based divertor in future fusion reactors. However, the formation of W/Y2O3 composite, melting and depletion of the Y2O3 particles gradually occurred with increasing the surface temperatures. It implies that the doping of Y2O3 particles complicates the plasma-material interaction, compared to the pure W case. For example, it raises concerns about the formation of complex dust which will potentially be a significant issue for the safe operation of future fusion reactors (e.g. core plasma contamination and fuel recycling).

Preparation and Thermal Shock Characterization of Yttrium Doped Tungsten-Potassium Alloy

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Properties of Potassium Doped and Tantalum Containing Tungsten after Heavy Ion Irradiation

Effect of Potassium Doping on the Thermal Shock Behavior of Tungsten

Influence of Surface Morphology and Microstructure on Performance of CVD Tungsten Coating under Fusion Transient Thermal Loads

Thermal Shock Performance of CVD Tungsten Coating at Elevated Temperatures

Thermal Shock Behavior of W-0.5 Wt% Y 2 O 3 Alloy Prepared Via a Novel Chemical Method

Surface Cracking of Tungsten-Vanadium Alloys under Transient Heat Loads

Thermal Shock Resistance of Nanocrystalline and Ultrafine-Grained W-Y2O3-Ti Alloys

Effect of Molybdenum Doping on the Microstructure, Micro-Hardness and Thermal Shock Behavior of WKMoTiY Alloy

Effect of potassium bubbles on the thermal shock fatigue behaviors of large-volume potassium-doped tungsten alloy

Room temperature ductile W-Y2O3 alloy with high thermal shock resistance

Microstructure characterization and properties of YSZ particles doped tungsten alloy prepared by liquid phase method

Room-temperature Tensile Strength and Thermal Shock Behavior of Spark Plasma Sintered W-K-TiC Alloys

Microstructural Effects of Y2O3 and TiC Additions in Tungsten

Response of yttria dispersion strengthened tungsten simultaneously exposed to steady-state and transient hydrogen plasma

DBTT and tensile properties of as-sintered tungsten alloys reinforced by yttrium-zirconium oxide

Surface Morphology and Microstructure Evolution of Trace Titanium and Yttrium in W-K-Mo-Ti-Y Alloys under Transient Heat Loads

Design of Highly Thermal-Shock Resistant Tungsten Alloys with Nanoscaled Intra- and Inter-Type K Bubbles

Surface Damage and Microstructure Evolution of Yttria Particle-Reinforced Tungsten Plate During Transient Laser Thermal Shock

Recrystallization Kinetics of Larger Yttria Particle Dispersion Tungsten Alloy Warm Rolled to 50% Thickness Reduction