Abstract:Copper-nickel alloys have received much attention in the last decades due to their high electrical, thermal, mechanical, and magnetic properties which mainly depend on their composition. In this paper, copper-nickel alloy coatings onto indium tin oxide substrate were elaborated by electrodeposition in pulsed current mode with optimized current density and deposition time. The electrodeposition is subsequently followed by thermal treatment under controlled atmosphere. The surface morphology and the chemical analysis of the elaborated coatings were assessed by scanning electron microscopy associated to x-ray microanalysis. Their structural analysis was performed by x-ray diffraction, and the Vickers microhardness test was conducted to examine their mechanical properties. Moreover, the adhesive strength of the copper-nickel coatings was evaluated using a progressive scratch test, while a multi-pass scratch test was employed to assess their wear resistance. The results showed that the copper-nickel coating obtained with optimized current density (− 20 mA/cm 2 ) and heat treated at 600 °C for 1 h under controlled atmosphere exhibits high mechanical properties; the microhardness increases from 133 to 280 HV, and the adhesion strength from 32 to 203 MPa. On the other hand, optimized electrodeposition conditions followed by thermal treatment led to thinner characteristic XRD pics of Cu-Ni coating indicating an increase in crystallinity from 12 nm to 44 nm. Mechanical characteristics underlined a high resistance to scratches, a decrease in the friction coefficient, and an increase in the dissipated energy which reaches 20 J for heat-treated Cu-Ni coating. These results highlighted a homogeneity in morphology, and low porosity improving the CuNi coatings adhesion strength to the substrate.

Nickel Coating on Alumina Ceramic Surface by Chemical Vapour Deposition and Its Wettability with Copper

Deposition Mechanism and Wear Resistance Nano Ni-Al2O3 Composite Coatings

Deposition Mechanism and Wear Resistance Nano Ni-Al<sub>2</sub>O<sub>3</sub> Composite Coatings

Nickel and copper deposition on fine alumina particles by using the chemical vapor deposition-circulation fluidized bed reactor technique

Preparation of coatings on alumina ceramic for wettability

Wetting Behaviors of Nickel-Based Alloys on Sintered Silicon Carbide Ceramics

Characteristics of Bonding Between Copper Coating Electroless Plated on Ni Ion Implanted Al2O3 Ceramic Surface and Substrate

Friction and Wear Characteristics of Electrodeposited Ni‐based Metallic Coatings on Cu‐substrate under High‐Temperature Conditions

Quick nickel metallization and magnetic properties on the surface of alumina powder

Investigation of wettability of copper plate with nickel-graphene oxide coating produced by electroplating method

Aluminum Co-Deposition via DC Magnetron Sputtering for Enhanced Pitting Resistance of Copper–Nickel Alloys

Heat Treatment Effects on the Microstructural and Mechanical Properties of Electrodeposited Cu-Ni Coatings

Electrochemical behavior and electro-crystallization mechanism of Cu-Ni/Nano-Al 2 O 3 coating with a deposition current density dependence

Corrosion and Wear Resistance of HVOF-Sprayed Ni-Cr-Co Multi-principal Element Alloy Coating on Copper Plate

Wetting Behaviors of Pure Nickel and Nickel-Based Alloys on Sintered ZrB2-SiC Ceramics

Influence of interfacial configuration on bonding strength and wettability between CuNiTi active filler metal and AlN ceramic

Electroless deposition of nickel on the surface of silicon carbide/aluminum composites in alkaline bath

Morphology Behavior of Copper Films Deposited after Wet Surface Treatment on Polished Alumina

Improving the properties of nickel/graphene oxide coated copper plate by changing the electroplating process conditions

Enhanced interfacial wettability and mechanical properties of Ni@Al2O3/Cu ceramic matrix composites using spark plasma sintering of Ni coated Al2O3 powders

Microstructure and excellent arc ablation resistance of Ni-8Al coating on copper substrate by high-speed laser cladding