Abstract:In previously reported low-fluorine MOD-YBCO studies, the lowest F/Ba mole ratio of the precursor solution was 4.5. Further lowering the F/Ba ratio would bring benefits for the environment, thick film deposition, and an understanding of the heat treatment process. On the other hand, the F/Ba ratio must be at least 2 for full conversion of the Ba-precursor to BaF2 to avoid the formation of BaCO3, which is detrimental to the superconducting performance of YBCO films. In this study, a solution with a 2:1 F/Ba mole ratio was developed, and the fluorine content of this solution was approximately only 10.3% of that used in the conventional TFA-MOD method. Attenuated total reflectance-Fourier transform-infrared spectra (ATR-FT-IR) revealed that BaCO3 was remarkably suppressed in the as-pyrolyzed film-and eliminated at 700 degrees C. Thus, YBCO films with a critical current density (J(c)) of over 5 MA cm(-2) (77 K, 0 T, 200 nm thickness) could be obtained on lanthanum aluminate single-crystal substrates. In situ FT-IR spectra showed that no obvious fluorinated gaseous by-products were detected in the pyrolysis step, which indicated that all F atoms might remain in the film as fluorides. X-ray diffraction theta/2 theta scans showed the presence of BaF2-but not of YF3 or CuF2-in films quenched at 400-800 degrees C. The formation priority of BaF2 over YF3 and CuF2 was interpreted by examining the chemical equilibrium of the potential reactions. Our study could enlarge the synthesis window of precursor solutions for MOD-YBCO fabrication, and serve as a foundation for continuously and systematically studying the influence of fluorine content in the precursor solutions.

Development Of Low-Fluorine Solution For Ybco Film Growth

Controlled-Growth of $\hbox{YBa}_{2}\hbox{Cu}_{3}\hbox{O}_{7-\delta} $ Film Using Modified Low-Fluorine Chemical Solution Deposition

Optimization of Fluorine Content in Tfa-Mod Precursor Solutions for Ybco Film Growth

Controlled-Growth of Yba2cu3o7-Delta Film Using Modified Low-Fluorine Chemical Solution Deposition

A Low-Fluorine Solution With A 2:1 F/Ba Mole Ratio For The Fabrication Of Ybco Films

A Low-Fluorine Solution with the F/Ba Mole Ratio of 2 for the Fabrication of YBCO Films

Decomposition and Oriented Growth of Yba2cu3o7-X Films Prepared with Low Fluorine Tfa-Mod Approach

Carbon Dioxide Controlled Thermal-Decomposition Reactions for Preparation of High Quality YBCO Films Derived from Fluorine-Free Solution

High Quality Ybco Film Growth on Srtio3-Buffered Laalo3 Substrate by Full Solution Method

Fluorine-free sol gel deposition of epitaxial YBCO thin films for coated conductors

Progress towards a low-cost commercial coated conductor

Highly (001)-oriented zirconium-doped ceria films grown on biaxially textured nickel tungsten substrates through an inorganic-salts-based chemical solution deposition route

Effect of precursor stoichiometry on the superconducting properties of fluorine-free sol–gel YBCO thin films

Preparation of Superconducting Yba2cu3o7-X Films on Metallic Substrates by Pulsed Laser Deposition

Enhanced Flux-Pinning Performance Of Ybco Films Derived From A Fluorine-Free Sol-Gel Process With Ceria Addition

Reel-To-Reel Continuous Deposition Of Ce(X)Zr(1-X)O(2) Single Buffer Layer For Ybco Coated Conductors

MOCVD Preparation of YBCO Coated Conductors on CeO2/YSZ/Y2O3 Buffered RABiTS Substrate

Thick $\Hbox{yba}_{2}\hbox{cu}_{3}\hbox{o}_{7-\Delta}$ Superconducting Films by Low-Fluorine Metallorganic Solution Deposition

YBCO Superconducting Thin Film Preparation on Metallic Substrates by Laser

Development of High Critical Current YBCO Coated Conductors by Photo-Assisted MOCVD

Fabrication And Analysis Of Tri-Layer Yba2cu3 O (7-Delta) Thick Films By Low-Fluorine Mod Method