Abstract:This paper presents the results of the Ni substrate wetted with the liquid Sn-Zn eutectic alloy with the addition of Ag, Al, and Li (84.3 at.% Sn, 13.7 at.% Zn, 1 at.% Ag, 0.5 at.% Al, and 0.5 at.% Li-SZAAL). The wetting tests were performed using two methods: the wetting balance tests (WBT) and the sessile drop (SD) method at 250 °C, in the presence of an ALU33® flux. The wetting times were 5, 20, 60, 180, and 1800 s. Next, the microstructure of selected solidified solder joints was investigated using scanning electron microscope. The Ni-Zn system's intermetallic phases (IMCs) were identified at the solder–Ni substrate interface. The kinetics of the formation and growth of the IMC layer was determined. Interfacial tension and contact angle (CA) values were calculated from WBT measurements in the presence of the ALU33® flux. Interfacial tension was compared to surface tension from the maximum bubble pressure and CA values to those obtained using the SD method. The value of the contact angle of SZAAL on Cu (39°) substrate is lower than on Ni (43°). For the comparison, also the interaction between SZAAL and Cu substrate was measured. After 1800 s, the IMCs thickness is significantly reduced for Ni pad than for Cu substrate. The study found that the addition of Al, Ag, and Li improved the tensile strength and wettability of Sn-Zn eutectic-based alloys.

Wetting and Spreading of Sn on Molten ZnCl2 Treated Amorphous Zr55Cu30Al10Ni5 Surface

Wetting and Interfacial Chemistry of New Pb-Free Sn-Zn-Ag-Al-Li (SZAAL) Solder with Cu, Ni, and Al Substrates

Soldering Zr metallic glass to Ti alloy using pre-cladding ultrasonic processes

Electrochemical Behavior of Zn-xSn High-Temperature Solder Alloys in 0.5 M NaCl Solution

Interfacial Reactions of Sn-8wt.%Zn-3wt.%Bi Solder with Cu, Ag, and Ni Substrates

Wetting Behavior and Interfacial Characteristics in the Molten Bi-Sn/High-Entropy Alloy System

Corrosion Process Study of Zn-30Sn High-Temperature Lead-Free Solder

Wetting Behaviors and Interfacial Reaction Between Sn-10Sb-5Cu High Temperature Lead-free Solder and Cu Substrate

Effect of Cr Addition on Wetting Behavior Between Cu and High-Temperature Zn-25Sn-0.15Al-0.1Ga-xCr Pb-Free Solder

Corrosion Mechanism of Zn-30Sn High-Temperature, Lead-Free Solder in Neutral NaCl Solution

Corrosion mechanisms of Zr-based bulk metallic glasses in NaBr solution

Interfacial reactions in the Sn–9Zn–(<i>x</i>Cu)/Cu and Sn–9Zn–(<i>x</i>Cu)/Ni couples

Interfacial reactions in the Sn–9Zn–( x Cu)/Cu and Sn–9Zn–( x Cu)/Ni couples

Wettability and spreading behavior of Sn–Cr alloys on SiC

Solid-state reactions between Sn-20.0 wt.%In- x wt.%Zn solders and Ag and Ni substrates

Intermetallic compound evolution and mechanical properties of Sn-0.7Cu-0.1Ni-xZn lead-free solder alloys prepared by directional solidification

Thermal Property, Wettability and Interfacial Characterization of Novel Sn–Zn–Bi–In Alloys As Low-Temperature Lead-Free Solders

EFFECTS OF THE ADDITION OF Ti OR Al ON THE WETTING BEHAVIORS AND INTERFACIAL CHARACTERISTICS OF Zr 50 Cu 50 BULK METALLIC GLASS/W SUBSTRATE

Electrochemical Corrosion Behavior, Microstructure and Soldering Properties of Tin Based Alloys

The wetting behavior of Al/Sn under ultrasonic action

Microstructural evolution of Sn-9Zn-3Bi and Sn-9Zn-3Bi-0.3Cr solder under high-temperature and high-humidity conditions