Abstract:Reactive melt infiltration (RMI) has been proved to be one of the most promising technologies for fabrication of C/SiC composites because of its low cost and short processing cycle. However, the poor mechanical and anti-ablation properties of the RMI-C/SiC composites severely limit their practical use due to an imperfect siliconization of carbon matrixes with thick walls and micron-sized pores. Here, we report a high-performance RMI-C/SiC composite fabricated using a carbon fiber reinforced nanoporous carbon (NC) matrix preform composed of overlapping nanoparticles and abundant nanopores. For comparison, the C/C performs with conventional pyrocarbon (PyC) or resin carbon (ReC) matrixes were also used to explore the effect of carbon matrix on the composition and property of the obtained C/SiC composites. The C/SiC derived from C/NC with a high density of 2.50 g cm -3 has dense and pure SiC matrix and intact carbon fibers due to the complete ceramization of original carbon matrix and the almost full consumption of inspersed silicon. In contrast, the counterparts based on C/PyC or C/ReC with a low density have a little SiC, much residual silicon and carbon, and many corroded fibers. As a result, the C/SiC from C/NC shows the highest flexural strength of 218.1 MPa and the lowest ablation rate of 0.168 μm s -1 in an oxyacetylene flame of ~ 2200 °C with a duration time of 500 s. This work opens up a new way for the development of high-performance ceramic matrix composites by siliconizing the C/C preforms with nanoporous carbon matrix

Fabrication and Properties of Lightweight SiOC Modified Carbon-Bonded Carbon Fiber Composites

Carbon-bonded Carbon Fiber Composites Containing Uniformly Distributed Silicon Carbide

Carbon-bonded Carbon Fiber Composites Reinforced with SiOC-based Polymer Derived Ceramics: Microstructure and Properties

SiOC Modified Carbon‐bonded Carbon Fiber Composite with SiC Nanowires Enhanced Interfibrous Junctions

Fabrication and Properties of Lightweight ZrB2 and SiC-modified Carbon Bonded Carbon Fiber Composites Via Polymeric Precursor Infiltration and Pyrolysis

Preparation and Properties of SiOC Ceramic Modified Carbon Fiber Needled Felt Preform Composites

Multifunction properties of SiOC reinforced with carbon fiber and in-situ SiC nanowires

Structure and Energetics of SiOC and SiOC‐modified Carbon‐bonded Carbon Fiber Composites

Preparation and anti-oxidation properties of Si(O)C coated carbon-bonded carbon fibre composites

Preparation and Mechanical Behaviors of SiOC-modified Carbon-Bonded Carbon Fiber Composite with In-Situ Growth of Three-Dimensional SiC Nanowires

Preparation and Characterization of SiO2/Carbon Foam and SIC/Carbon Foam Composites

Precursor Infiltration and Pyrolysis Cycle-Dependent Microwave Absorption and Mechanical Properties of Lightweight and Antioxidant Carbon Fiber Felts Reinforced Silicon Oxycarbide Composites.

Microwave absorption and mechanical properties of SiCf/SiOC composites with SiO2 fillers

Mechanical properties and strengthening mechanism of SiCf/SiC mini-composites modified by SiC nanowires

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

Effects of chopped carbon fiber on the forming, structure and mechanical properties of CCF/SiC composites fabricated by SLS and RMI

Microstructural Regulation, Oxidation Resistance and Mechanical Properties of Cf/SiC/SiHfBOC Composites Prepared by Chemical Vapor Infiltration with Precursor Infiltration Pyrolysis

Lightweight carbon-bonded carbon fiber composites with quasi-layered and network structure

Novel Csf/SiBCN Composites Prepared by Densifying Csf/MA-SiBCN with the PIP Process: Oxidation Behavior and Damage Mechanism

Microstructure and mechanical properties of 3D Cf/SiBCN composites fabricated by polymer infiltration and pyrolysis

Study of Rapid Fabrication and Microstructure of C/C-SiC Composites