Abstract:TiAl intermetallic compounds, as a new kind of high-performance light-weight structural material, are widely applied in many fields. Titanium carbide (TiC) as the reinforcing phase could improve the mechanical properties, wear resistance, and heat-resistance stability of TiAl intermetallic compounds. Ti(Al, C) mixture powders were deposited by cold spraying at gas temperature of 250 °C, 450 °C, and 550 °C. Then, Ti(Al, C) coatings were annealed at temperatures of 650 °C for different times and following holding at 1100 °C for 3 h. The microstructure, microhardness, fracture toughness, and abrasive wear of Ti-Al composite coatings were investigated. The research results were that the particle size of mixture powders decreased as the ball milling time prolonging. Ti(Al) solid solution appeared in the mixture powders as the milling time increased to 30 h. The average porosity of the coating sprayed at 550 °C was the lowest (0.85%). The as-sprayed coatings exhibited the same phase compositions with the mixture powders. The coating sprayed at gas temperature of 550 °C has the highest microhardness and the lowest weight loss. Ti-Al intermetallic was in-situ synthesized after annealing at 650 °C. The average porosity of the annealed coating (sprayed at 450 °C) was the lowest. The content of Ti-Al intermetallic compounds of the annealed coating sprayed at 450 °C is the highest. The X-ray diffraction (XRD) analysis results are consistent with the EDS analysis of the annealed coatings after annealing at 650 °C. Ti-Al intermetallic compounds were almost completely formed in the three kinds of the coatings after annealing at 650 °C for 20 h and following holding at 1100 °C for 3 h. TiAl and TiAl3 intermetallic phases were in-situ synthesized in the coatings based on the energy dispersive spectroscopy (EDS) and XRD analysis. TiC was also in situ synthesized in the coatings as the annealing temperature increased to 1100 °C. The annealed coating (sprayed at 450 °C) has the highest microhardness, fracture toughness, and wear resistance properties after annealing at 1100 °C for 3 h.

Microstructures, Mechanical and Oxidation Behaviors of C/C Composites Modified by NiAl Alloy

Study on Microstructure and Mechanical Properties Modification of Cu-Ti3AlC2 Composites by Ni Element

Interpenetrating microstructure and fracture mechanism of NiAl/TiC composites by pressureless melt infiltration

Effect of Cu/Ni coating on the interface and mechanical properties of C f /2024Al composites

Preparation of in situ TiC@TiN core–shell and Ti2N–Al4C3 nanoparticles and their effects on Al–Zn–Mg–Cu alloy

Microstructure and Mechanical Properties of Ti2AlC-reinforced TiAl Composites

The Effect of Coating Grain Size on the Selective Oxidation Behaviour of Ni-Cr-Al Alloy

Microstructures and properties of in situ synthesis Ni/Ni-Al multilayer composites

Investigation on microstructure and properties of TiC0.5-Al2O3/Cu composites fabricated by a novel in-situ reactive synthesis

The effect of nickel coating on the mechanical properties and failure modes of continuous carbon fiber reinforced aluminum matrix composites

Investigation on NiAl–TiC–Al2O3 Composite Prepared by Self-Propagation High Temperature Synthesis with Hot Extrusion

Effect of surface modification on interfacial microstructures and mechanical properties of continuous CF/Al composites

Microstructure and High-Temperature Mechanical Properties of CrMnFeCoNi/TiAl Composites Prepared by Powder Metallurgy

Effect of Ti–Cu alloy's composition on microstructure and performance of carbon fiber reinforced TiC-based composites prepared by alloyed reactive melt infiltration

Fabrication, microstructure and mechanical properties of TiAl matrix composite reinforced by submicro/nano-Ti 2 AlC

Microstructures, mechanical properties, and oxidation behavior of in-situ ultra-fine duplex carbides reinforced Ni-based superalloy composites

Investigation on Microstructure and Wear Behavior of the NiAl–TiC–Al2O3 Composite Fabricated by Self-Propagation High-Temperature Synthesis with Extrusion

Effects of the addition of CNTs and Al alloying on the microstructure and properties of Cu-(Al)/CNTs composites

Microstructure, Microhardness, Fracture Toughness, and Abrasive Wear of In-Situ Synthesized TiC/Ti-Al Composite Coatings by Cold Spraying Combined with Heat Treatment

Microstructure and high-temperature oxidation behavior of Ti3AlC 2/W composites

Antioxidant Behavior of Carbon/Carbon Composites with Hot Dip Plating and Electroplating for Single-Crystal Furnaces