Abstract:In order to reveal the relationship between microstructure inhomogeneity and mechanical anisotropy, the Al–Cu–Li alloy 100 mm thick plate for aerospace was evaluated. The grain structure, crystallographic texture, phase structure and fractography of different thickness positions and directions were observed by optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). The in-plane and through-thickness anisotropy were characterized by tensile properties, fracture toughness and hardness tests. The results demonstrate a greater in-plane anisotropy in yield strength at the same thickness position of the plate. The Brass texture component increases successively at T, T/4, and T/2 positions, while the Cu texture component exhibits minimal variation. The in-plane anisotropy mainly arises from the Brass texture. Through-thickness anisotropy in the same direction is primarily influenced by the diameter, number density, and volume fraction of the T1 strengthening phase. The average diameter and number density of the primary strengthening phase T1 within grains are highest at the T/2 position and lowest at the T position. The plate contains unrecrystallized, elongated pancake-like grains along the rolling direction. Fracture toughness tests conducted in the L-T and T-L directions predominantly reveal dimple-type transgranular shear fractures, while the S-L direction exhibits intergranular fracture as the primary characteristic. The crack divider delamination toughening mechanism is the main contributor to higher fracture toughness values in the L-T and T-L directions compared to those in the S-L direction. The results reveal the corresponding relationship between the microstructure inhomogeneity and the mechanical anisotropy of Al–Li alloy ultra-thick plates, and provide ideas for the adjustment of process parameters during processing deformation and the regulation of microstructure during heat treatment of large-scale Al–Li alloy thick plates, which has engineering application reference value.

XTEM STUDY ON ION-PLATWG ALUMINUM BRONZE FILM

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

Recent Electron Microscopy Results on Micro- and Nanostructured Ni-Ti-(X) Shape Memory Alloys

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Study on Precipitation in (cocrfemnni)90al6ti4 High Entropy Alloy

Morphology and Fracture of Oxide Bifilm Defects in Nickel-Aluminium Bronze

Microstructure, Morphology and Their Annealing Behaviors of Alumina Films Synthesized by Ion Beam Assisted Deposition

Structure of oxide bifilms in nickel-aluminium bronze alloys

TEM Observation of General Growth Behavior for Silver Electroplating on Copper Rod

Corrosion Behavior of Aluminum Bronze under Thin Electrolyte Layers Containing Artificial Seawater

Growth Mechanism and Microstructure of Al Films Deposited on Ionic Liquid Surfaces

In-situ TEM study on the precipitation behavior of an Al-Mn-Mg-Sc-Zr alloy formed by SLM

TEM Study on the Microstructure of the Zn-Al-Mg Alloy

Morphology Behavior of Copper Films Deposited after Wet Surface Treatment on Polished Alumina

Design of amorphous-nanocrystalline films of TiAlCrNbZr x multi-component alloy: The effect of Zr on the corrosion resistance and mechanical properties

Structure of the Copper–Enriched Layer Introduced by Anodic Oxidation of Copper-Containing Aluminium Alloy

An In-Situ TEM Investigation on Microstructure Evolution of Ni-25 At.% Al Thin Films

Ex Situ Tem Observation of Localized Attack on Aa 6061

Microstructure and texture distribution in the bonding interface of Cu/Al composite tube fabricated by explosive welding

Effect of microstructural inhomogeneity on mechanical anisotropy of Al–Cu–Li alloy plate

Effect of Preparation Method on Film Structure and Thermal Stability of Me/MeN/Me (me = Al, Ti) Multilayer Thin Films