Abstract:In order to obtain softer polyolefins applicable as toughener for polypropylene (PP), a series of in-reactor alloys composed of polyethylene, crystalline ethylene-propylene copolymer (cEP) and amorphous ethylene-propylene copolymer (aEP) were synthesized by sequential ethylene polymerization followed by ethylene-propylene copolymerization in periodic switching polymerization process (PSPP) using a spherical MgCl2-supported Ziegler-Natta catalyst. In the PSPP step, ethylene-propylene copolymerization was repeatedly switched between two different monomer feed ratios: one with high propylene/ethylene ratio to form aEP component, and the other with low propylene/ethylene ratio to form cEP component. In the synthesized PE/cEP/aEP in-reactor alloys, aEP accounted for 40∼56 wt.%, and cEP accounted for 18∼30 wt.% of the alloy. With aEP content rising above 48 wt.%, the alloys showed rather low modulus, and no yielding appeared in their stress-strain curve, implying that they were a sort of elastomeric material. By blending the PE/cEP/aEP alloys with isotactic PP, their PP-toughening performances were evaluated and compared with a commercial EPDM. Impact strength of PP toughened by the alloy was significantly higher than that toughened by EPDM at the same blend ratio. Cryo-fractured surface of PP/alloy blends showed that the alloy particles were uniformly dispersed in PP matrix, and showed a core-shell type morphology, in which the core domain was composed of polyethylene, and aEP constituted the shell domain in between the core and the PP matrix. Segmented EP copolymer chains (s-EP) located inside the aEP domains formed thin filaments bridging the core and the PP matrix, which are believed to act as compatibilizer that significantly enhanced interfacial adhesion between the PP matrix and the dispersed phase.

Synthesis of Polyethylene/poly(ethylene-Co-propylene) In-Reactor Alloys by Periodic Switching Polymerization Process: Effects of Switching Frequency on Polymer Structure and Properties

Regulation of Structure and Mechanical Properties of Poly(propylene-Butene) Alloys by Monomer Composition Switching

Synthesis of Polypropylene/poly(ethylene-co-propylene) In-Reactor Alloys by Periodic Switching Polymerization Process: Dynamic Change of Gas-Phase Monomer Composition and Its Influences on Polymer Structure and Properties

Effects of Switching Frequency of a Periodic Switching Polymerization Process on the Microstructures of Ethylene–Propylene Copolymers in Polypropylene/Poly(ethylene-co-propylene) In-Reactor Alloys

Polypropylene and Ethylene−Propylene Copolymer Reactor Alloys Prepared by Metallocene/Ziegler−Natta Hybrid Catalyst

Synthesis of Polypropylene/Poly(Ethylene-Co-Propylene) In-Reactor Alloys by Periodic Switching Polymerization Process-Effects of Gas Phase Polymerization Time on Polymer Properties

I-Pp/epr REACTOR ALLOY PREPARED THROUGH ETHYLENE/PROPYLENE SLURRY COPOLYMERIZATION CATALYZED BY METALLOCENE SUPPORTED Ipp PARTICLES

Structural Parameters in Relation to the Rheological Behavior and Properties of PP/EPR In‐reactor Alloy Synthesized by Multi‐stage Sequential Polymerization

Control of Diffusion/Barrier Effects of Polymer-Coated Particles and the Strengthening of Ethylene Polymerization Reactor

Polymerization-induced phase separation in polyethersulfone modified epoxy resin systems: effect of curing reaction mechanism

Synthesis of high performance PE/PP/EPR in-reactor alloys by sequential multi-stage gas-phase polymerization with spherical Ziegler-natta catalyst

Enhanced Multiphase Interfacial Interaction of Impact Polypropylene Copolymer by In-Situ Introducing Polyethylene

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Research on Toughening Modification of Copolymerized Polypropylene Using Polyolefin Elastomers

Influence of Copolymerization Conditions on the Structure and Properties of Polyethylene/Polypropylene/Poly(Ethylene-Co-Propylene) In-Reactor Alloys Synthesized in Gas-Phase with Spherical Ziegler-Natta Catalyst

Preparation and Characterization of High MFR Polypropylene and Polypropylene/poly(ethylene‐co‐propylene) In‐reactor Alloys

Chain structure and mechanical properties of polyethylene/polypropylene/poly(ethylene-co-propylene)in-reactor alloys synthesized with a spherical Ziegler-Natta catalyst by gas-phase polymerization

Influence of Polymerization Conditions on the Structure and Properties of Polyethylene/polypropylene In‐reactor Alloy Synthesized in the Gas Phase with a Spherical Ziegler–Natta Catalyst

Synthesis of High Quality PE/PP In-Reactor Alloys with PE Matrix by Multi-Stage Polymerization

Polyethylene/crystalline ethylene-propylene copolymer/amorphous ethylene-propylene copolymer in-reactor alloys synthesized by periodic switching polymerization process: An excellent toughener for polypropylene

Dynamic Shear Rheological Behavior of PP/EPR In‐reactor Alloys Synthesized by Multi‐stage Sequential Polymerization Process