Abstract:It is of great importance to polymerize multivinyl monomers and simultaneously circumvent uncontrollable polymerization process and low gel point. Hereby, a type of divinyl monomer: ethylene glycol dimethacrylate (EGDMA) was successfully homopolymerized by kinetically controlled Cu-0 and Cu-II-meadiated reversible-deactivation radical polymerization (RDRP). The kinetic study showed a well-controlled polymerization behaviour. During the initial stage, a linear chain propagation was observed with a low polydispersity (< 1.35) demonstrating the controlled/living polymerization feature. However, the products obtained during this stage showed a high consumption of pendent vinyl groups (around 28%) based on the analysis by proton nuclear magnetic resonance (H-1-NMR). This high pendent vinyl conversion in the linear chain propagation stage is attributed to the significant involvement of the intramolecular cyclization. The promotion of the intramolecular cyclization and suppression of the intermolecular crosslinking is achieved by the low kinetic chain length and low polymer volume concentration. Given the coexistence of linear chain propagation and high pendent vinyl conversion, the novel single chain cyclized polymer structure was formed during this process, which was further used as polymeric nanoparticles to modify the viscoelasticity of linear poly(methyl methacrylate) (PMMA) melts. The essentially similar chemical structure between the EGDMA and MMA ensures the minimization of enthalpic interactions and dispersion forces between the nanoparticles and linear melts. The oscillatory rheology study and the subsequent time temperature superposition based on the Williams-Landel-Ferry equation demonstrated the coexistence of the segmental relaxation at high frequencies and chain relaxation at low frequencies. The complex viscosity studied as a function of the shear frequency showed the decrease in terminal viscosity with addition of 10 wt% single chain cyclized polyEGDMA nanoparticles. A further decrease was also observed with the addition of 20 wt% nanoparticles, which is not in agreement with Einstein relationship between the complex viscosity and fraction of added particles. This strategy provides a simple and efficient approach to control polymerization of multivinyl monomers, and the unexpected decrease in viscosity of the blend system should in principle open a new avenue to modify polymer melts and molten systems.

Dynamic Shear Rheological Behavior of PP/EPR In‐reactor Alloys Synthesized by Multi‐stage Sequential Polymerization Process

Structural Parameters in Relation to the Rheological Behavior and Properties of PP/EPR In‐reactor Alloy Synthesized by Multi‐stage Sequential Polymerization

Viscoelastic Effects on the Phase Separation in Thermoplastics-Modified Epoxy Resin

Synthesis of Polypropylene/poly(ethylene-co-propylene) In-Reactor Alloys by Periodic Switching Polymerization Process: Dynamic Change of Gas-Phase Monomer Composition and Its Influences on Polymer Structure and Properties

Polypropylene and Ethylene−Propylene Copolymer Reactor Alloys Prepared by Metallocene/Ziegler−Natta Hybrid Catalyst

Rheological Behaviors and Structural Transitions in A Polyethersulfone-Modified Epoxy System During Phase Separation

I-Pp/epr REACTOR ALLOY PREPARED THROUGH ETHYLENE/PROPYLENE SLURRY COPOLYMERIZATION CATALYZED BY METALLOCENE SUPPORTED Ipp PARTICLES

Polymerization-induced viscoelastic phase separation in polyethersulfone-modified epoxy systems.

Effect of Phase Structure on the Viscoelasticity and Mechanical Properties of Isotactic Polypropylene Multicomponent Polymerized with Non-Conjugated α,ω-Diene

Viscoelastic Study of Single Chain Cyclized Polymeric Nanoparticles and Linear Polymers Blends

Effects of Switching Frequency of a Periodic Switching Polymerization Process on the Microstructures of Ethylene–Propylene Copolymers in Polypropylene/Poly(ethylene-co-propylene) In-Reactor Alloys

Rheological Behavior and Nonisothermal Crystallization of Polypropylene/Epoxidized Natural Rubber Blends

Morphology of Polypropylene/Poly(Ethylene-Co-Propylene) In-Reactor Alloys Prepared by Multi-Stage Sequential Polymerization and Two-Stage Polymerization

Synthesis of Polyethylene/poly(ethylene-Co-propylene) In-Reactor Alloys by Periodic Switching Polymerization Process: Effects of Switching Frequency on Polymer Structure and Properties

Preparation and Characterization of High MFR Polypropylene and Polypropylene/poly(ethylene‐co‐propylene) In‐reactor Alloys

Study on Liquid-Liquid Phase-Separation and Its Effect on the Crystallization Kinetics of Blends Composed of Isotactic Polypropylene/Ethylene-Propylene Rubber

Effect of Microstructure of Epr on Crystallization and Morphology of Pp/Epr Blends

Synthesis of high performance PE/PP/EPR in-reactor alloys by sequential multi-stage gas-phase polymerization with spherical Ziegler-natta catalyst

Crystallization kinetics and morphology of iso-PP/ethylene-propylene-b- copolymer/ ethylene-propylene-r-copolymer ternary blends

Dynamic Rheological Behavior of Polypropylene Filled with Ultra-Fine Powdered Rubber Particles

Rheology Study on Polypropylene Blends with in situ Core-Shell Dispersed Particles