Abstract:In order to adapt hydrotalcite based sorbents (LDO) to high temperature CO2 sorption and suitable temperature for tar steam reforming, the addition of CaO was investigated, maintaining their structure to keep porosity and accessibility but mostly assure the CO2 sorption stability during sorption/desorption cycles. In co-precipitation synthesis, various interlayer anions with different sizes and valences (carbonate, oxalate, and stearate) and various pH values were studied for different Mg/Ca ratios. The characterization of these sorbents (LDO) by TGA, XRD, N2 adsorption, SEM, sorption capacity, and sorption/desorption stability (cyclic TGA) permitted to understand the effect of the various synthesis conditions and to highlight the interest of oxalate use as interlayer anion. Typical LDH sand roses were formed with carbonate and oxalate anions after calcination until Mg/Ca/Al ratio = 1/2/1. For carbonate, this optimal ratio reached the highest sorption capacity and CaO sites accessibility at 600°C, better than pure CaO. However, the best stability during cycles was obtained with the sorbent from oxalate and Mg/Ca/Al ratio = 1.5/1.5/1 at pH 10 for which sorption results were almost the best values observed. For these two samples, the observed macroporosity were associated to the highest specific surface area and pore volume.Statement of NoveltyIn hydrotalcite structure, a width interlayer space permits to integrate various anions (CO32-, SO4-2, or NO3-) in order to modify CO2 sorption kinetics and capacity. The spheroidal “sand rose” morphology observed with CO32- anions explained the large BET surface area and the better CO2 sorption capacity. Stearate (and longer molecules) exchange was extensively studied as long-carbon-chain organic anion and allowed a better CO2 capture performance.This work focuses on another interlayer anion (oxalate) with the same valence of carbonate (2), a shape and valence different to stearate (1), and not yet reported in the literature. The novelty is to demonstrate that oxalate can replace carbonate as interlayer anion and moreover stearate by a less toxic one.

Development of carboxyl-layered double hydrotalcites of enhanced CO 2 capture capacity by K 2 CO 3 promotion

Aqueous miscible organic-layered double hydroxides with improved CO 2 adsorption capacity

Dynamic Intermediate-Temperature CO2 Adsorption Performance of K2CO3-Promoted Layered Double Hydroxide-Derived Adsorbents

Promotion of MgO Sorbents with Eutectic Carbonate Doping for High-Temperature and Pressure CO2 Capture

Organic Anion Modified K-Promoted Hydrotalcite Adsorbent

High-Performance Co2 Adsorbent from Inter Layer Potassium-Promoted Stearate-Pillared Hydrotalcite Precursors

Synthesis of Elevated Temperature CO2 Adsorbents from Aqueous Miscible Organic-Layered Double Hydroxides

Modified Layered Double Hydroxides for Efficient and Reversible Carbon Dioxide Capture from Air

In situ growth of ZIF-8 nanocrystals on layered double hydroxide nanosheets for enhanced CO2 capture.

Evaluation of the Behavior of Hydrotalcite Like-Materials for CO2 Capture

Ca-Based Layered Double Hydroxides for Environmentally Sustainable Carbon Capture

Mesoporous alumina-supported layered double hydroxides for efficient CO2 capture

Preparation of amino-functionalized CoAl-LDH/palygorskite hierarchical composites for CO 2 capture

Structure and CO2 Physisorption Capacity of Hydrotalcite-Derived Oxide

Design, characterization and scale-up test of a high performance pre-combustion CO2 adsorbent

Enhancing Adsorbent Performance for Direct Air Capture of CO2 by In-Situ Amine-Grafting of Layered Double Hydroxides

Structural engineering of NiFe-Layered double hydroxides and halloysite composites for efficient CO 2 capture

Development of a high temperature CO2 sorbent based on hydrotalcite for a H2-rich syngas production from biomass.

Characterization and Structure Evolution of Ca-Al-CO3 Hydrotalcite Film for High Temperature CO2 Adsorption.

Layered double hydroxides for CO2 adsorption at moderate temperatures: Synthesis and amelioration strategies

Facile Preparation of Porous CaMgAl Hydrotalcite-Like Derived Mixed Oxides through Alkaline Etching of KOH for CO2 Capture