Abstract:The process of carbon dioxide capture typically requires a large amount of energy for the separation of carbon dioxide from other gases, which has been a major barrier to the widespread deployment of carbon capture technologies. Innovation of carbon dioxide adsorbents is herein vital for the attainment of a sustainable carbon capture process. In this study, we investigated the electrified synthesis and rejuvenation of calcium-based layered double hydroxides (Ca-based LDHs) as solid adsorbents for CO2. We discovered that the particle morphology and phase purity of the LDHs, along with the presence of secondary phases, can be controlled by tuning the current density during electrodeposition on a porous carbon substrate. The change in phase composition during carbonation and calcination was investigated to unveil the effect of different intercalated anions on the surface basicity and thermal stability of Ca-based LDHs. By decoupling the adsorption of water and CO2, we showed that the adsorbed water largely promoted CO2 adsorption, most likely through a sequential dissolution and reaction pathway. A carbon capture capacity of 4.3 ± 0.5 mmol/g was measured at 30 °C and relative humidity of 40% using 10 vol % CO2 in nitrogen as the feed stream. After CO2 capture occurred, the thermal regeneration step was carried out by directly passing an electric current through the conductive carbon substrate, known as the Joule-heating effect. CO2 was found to start desorbing from the Ca-based LDHs at a temperature as low as 220 °C as opposed to the temperature above 700 °C required for calcium carbonate that forms as part of the Ca-looping capture process. Finally, we evaluated the cumulative energy demand and environmental impact of the LDH-based capture process using a life cycle assessment. We identified the most environmentally concerning step in the process and concluded that the postcombustion CO2 capture using LDH could be advantageous compared with existing technologies.

Aqueous miscible organic-layered double hydroxides with improved CO 2 adsorption capacity

Synthesis of Elevated Temperature CO2 Adsorbents from Aqueous Miscible Organic-Layered Double Hydroxides

Development of carboxyl-layered double hydrotalcites of enhanced CO 2 capture capacity by K 2 CO 3 promotion

Dynamic Intermediate-Temperature CO2 Adsorption Performance of K2CO3-Promoted Layered Double Hydroxide-Derived Adsorbents

Modified Layered Double Hydroxides for Efficient and Reversible Carbon Dioxide Capture from Air

Mesoporous alumina-supported layered double hydroxides for efficient CO2 capture

Enhancing Adsorbent Performance for Direct Air Capture of CO2 by In-Situ Amine-Grafting of Layered Double Hydroxides

Roles for K2CO3 Doping on Elevated Temperature CO2 Adsorption of Potassium Promoted Layered Double Oxides

Preparation of amino-functionalized CoAl-LDH/palygorskite hierarchical composites for CO 2 capture

Scalable Synthesis of Amine-Grafted Ultrafine Layered Double Hydroxide Nanosheets with Improved Carbon Dioxide Capture Capacity from Air

Synthesis, characterization, and CO(2) adsorptive behavior of mesoporous AlOOH-supported layered hydroxides.

Structural engineering of NiFe-Layered double hydroxides and halloysite composites for efficient CO 2 capture

Basic Properties of MgAl-Mixed Oxides in CO2 Adsorption at High Temperature

High-Performance Co2 Adsorbent from Inter Layer Potassium-Promoted Stearate-Pillared Hydrotalcite Precursors

Improving the adsorption capacity of amino-modified Mg-Al LDH using a combined DFT and experiment

Evaluation of the Behavior of Hydrotalcite Like-Materials for CO2 Capture

Comprehensive Analysis of the Chemical and Structural Transformations of Mg–Al–CO3 Layered Double Hydroxides with Different Mg/Al Ratios at Elevated Temperatures

Ca-Based Layered Double Hydroxides for Environmentally Sustainable Carbon Capture

Acetate intercalated Mg-Al layered double hydroxides (LDHs) through modified amide hydrolysis: a new route to synthesize novel mixed metal oxides (MMOs) for CO2 capture

Self-Assembled Core-Shell Structure MgO@TiO2 as a K2CO3 Support with Superior Performance for Direct Air Capture CO2

Facile Preparation of Porous CaMgAl Hydrotalcite-Like Derived Mixed Oxides through Alkaline Etching of KOH for CO2 Capture