Abstract:In order to adapt hydrotalcite based sorbents (LDO) to high temperature CO2 sorption and suitable temperature for tar steam reforming, the addition of CaO was investigated, maintaining their structure to keep porosity and accessibility but mostly assure the CO2 sorption stability during sorption/desorption cycles. In co-precipitation synthesis, various interlayer anions with different sizes and valences (carbonate, oxalate, and stearate) and various pH values were studied for different Mg/Ca ratios. The characterization of these sorbents (LDO) by TGA, XRD, N2 adsorption, SEM, sorption capacity, and sorption/desorption stability (cyclic TGA) permitted to understand the effect of the various synthesis conditions and to highlight the interest of oxalate use as interlayer anion. Typical LDH sand roses were formed with carbonate and oxalate anions after calcination until Mg/Ca/Al ratio = 1/2/1. For carbonate, this optimal ratio reached the highest sorption capacity and CaO sites accessibility at 600°C, better than pure CaO. However, the best stability during cycles was obtained with the sorbent from oxalate and Mg/Ca/Al ratio = 1.5/1.5/1 at pH 10 for which sorption results were almost the best values observed. For these two samples, the observed macroporosity were associated to the highest specific surface area and pore volume.Statement of NoveltyIn hydrotalcite structure, a width interlayer space permits to integrate various anions (CO32-, SO4-2, or NO3-) in order to modify CO2 sorption kinetics and capacity. The spheroidal “sand rose” morphology observed with CO32- anions explained the large BET surface area and the better CO2 sorption capacity. Stearate (and longer molecules) exchange was extensively studied as long-carbon-chain organic anion and allowed a better CO2 capture performance.This work focuses on another interlayer anion (oxalate) with the same valence of carbonate (2), a shape and valence different to stearate (1), and not yet reported in the literature. The novelty is to demonstrate that oxalate can replace carbonate as interlayer anion and moreover stearate by a less toxic one.

Development of a high temperature CO2 sorbent based on hydrotalcite for a H2-rich syngas production from biomass.

Properties of a Nano CaO/Al2O3 CO2 Sorbent

Ca based high temperature CO2 absorbents for sorption enhanced reforming process

Regenerable MgO-based Sorbents for CO2 Capture at Elevated Temperature and Pressure: Experimental and DFT Study

Promotion of MgO Sorbents with Eutectic Carbonate Doping for High-Temperature and Pressure CO2 Capture

Characteristics of MgO-based Sorbents for CO2 Capture at Elevated Temperature and Pressure

Properties of a Nano CaO/Al<sub>2</sub>O<sub>3</sub>CO<sub>2</sub>Sorbent

Developing a Novel CaO-Based Sorbent for Promoted CO2 Capture and Tar Reduction

Ca-rich Ca-Al-oxide, high-temperature-stable sorbents prepared from hydrotalcite precursors: synthesis, characterization, and CO2 capture capacity.

High-temperature CO 2 sorbents with citrate and stearate intercalated Ca–Al hydrotalcite-like as precursor

Development of Highly Effective CaO@Al2O3 with Hierarchical Architecture CO2 Sorbents Via a Scalable Limited-Space Chemical Vapor Deposition Technique

Evaluation of the Behavior of Hydrotalcite Like-Materials for CO2 Capture

Synthesis of Elevated Temperature CO2 Adsorbents from Aqueous Miscible Organic-Layered Double Hydroxides

CO2 Sorbents with Scaffold‐like CaAl Layered Double Hydroxides As Precursors for CO2 Capture at High Temperatures

Synthesis and Performance of a Nano Synthetic Ca-based Sorbent for High Temperature CO_2 Capture

A green and scalable synthesis of highly stable Ca-based sorbents for CO2 capture

New insights into stabilizing mechanism of Ca9Al6O18 stabilizing Ca-based sorbents for CO2 cyclic capture under mild conditions

Synthesis of CaO-based Sorbents Through Incorporation of Alumina/aluminate and Their CO2 Capture Performance

High-Entropy Fluorite Oxide-Modified CaO-Based Sorbent Pellets for Enhanced High-Temperature CO2 Capture

Application of the sol-gel technique to develop synthetic calcium-based sorbents with excellent carbon dioxide capture characteristics.

Hydrophobic interface-assisted casting of Al-supported, CaO-based sorbent pellets for high-temperature CO 2 capture