Abstract:In order to adapt hydrotalcite based sorbents (LDO) to high temperature CO2 sorption and suitable temperature for tar steam reforming, the addition of CaO was investigated, maintaining their structure to keep porosity and accessibility but mostly assure the CO2 sorption stability during sorption/desorption cycles. In co-precipitation synthesis, various interlayer anions with different sizes and valences (carbonate, oxalate, and stearate) and various pH values were studied for different Mg/Ca ratios. The characterization of these sorbents (LDO) by TGA, XRD, N2 adsorption, SEM, sorption capacity, and sorption/desorption stability (cyclic TGA) permitted to understand the effect of the various synthesis conditions and to highlight the interest of oxalate use as interlayer anion. Typical LDH sand roses were formed with carbonate and oxalate anions after calcination until Mg/Ca/Al ratio = 1/2/1. For carbonate, this optimal ratio reached the highest sorption capacity and CaO sites accessibility at 600°C, better than pure CaO. However, the best stability during cycles was obtained with the sorbent from oxalate and Mg/Ca/Al ratio = 1.5/1.5/1 at pH 10 for which sorption results were almost the best values observed. For these two samples, the observed macroporosity were associated to the highest specific surface area and pore volume.Statement of NoveltyIn hydrotalcite structure, a width interlayer space permits to integrate various anions (CO32-, SO4-2, or NO3-) in order to modify CO2 sorption kinetics and capacity. The spheroidal “sand rose” morphology observed with CO32- anions explained the large BET surface area and the better CO2 sorption capacity. Stearate (and longer molecules) exchange was extensively studied as long-carbon-chain organic anion and allowed a better CO2 capture performance.This work focuses on another interlayer anion (oxalate) with the same valence of carbonate (2), a shape and valence different to stearate (1), and not yet reported in the literature. The novelty is to demonstrate that oxalate can replace carbonate as interlayer anion and moreover stearate by a less toxic one.

High-temperature CO 2 sorbents with citrate and stearate intercalated Ca–Al hydrotalcite-like as precursor

Properties of a Nano CaO/Al2O3 CO2 Sorbent

Ca based high temperature CO2 absorbents for sorption enhanced reforming process

A new nano CaO-based CO2 adsorbent prepared using an adsorption phase technique

Adsorption Properties of Coating Modified Nano CaO-Based CO2 Adsorbents

Properties of a Nano CaO/Al<sub>2</sub>O<sub>3</sub>CO<sub>2</sub>Sorbent

Regenerable MgO-based Sorbents for CO2 Capture at Elevated Temperature and Pressure: Experimental and DFT Study

Characteristics of MgO-based Sorbents for CO2 Capture at Elevated Temperature and Pressure

Promotion of MgO Sorbents with Eutectic Carbonate Doping for High-Temperature and Pressure CO2 Capture

Developing a Novel CaO-Based Sorbent for Promoted CO2 Capture and Tar Reduction

New insights into stabilizing mechanism of Ca9Al6O18 stabilizing Ca-based sorbents for CO2 cyclic capture under mild conditions

Synthesis and Performance of a Nano Synthetic Ca-based Sorbent for High Temperature CO2 Capture

Efficient MgO-doped CaO sorbent pellets for high temperature CO2 capture

Development of a high temperature CO2 sorbent based on hydrotalcite for a H2-rich syngas production from biomass.

Hydrophobic interface-assisted casting of Al-supported, CaO-based sorbent pellets for high-temperature CO 2 capture

Facile Preparation of Porous CaMgAl Hydrotalcite-Like Derived Mixed Oxides through Alkaline Etching of KOH for CO2 Capture

Study on CO2 Capture Performance by Potassium-Promoted MgAl-Hydrotalcite Adsorbent

Studies on CO2 uptake by CaO/Ca3Al2O6 sorbent in calcium looping cycles

High-Entropy Fluorite Oxide-Modified CaO-Based Sorbent Pellets for Enhanced High-Temperature CO2 Capture

Strengthening performance of Al-stabilized, CaO-based CO 2 sorbent pellets by the combination of impregnated layer solution combustion and graphite-moulding

The Nanofibrous CaO Sorbent for CO2 Capture