Abstract:High-performance cast Al-Li alloys are highly desirable for a wide range of weight-critical and stiffness-critical applications. This work was undertaken to investigate the microstructural evolution, coarsening kinetics of main precipitates and related mechanical characteristics of a newly-developed cast Al-Li-Cu-Mg-X alloy during aging at 150, 175, 200 and 225 degrees C. The as-aged alloys studied primarily comprised of delta' (Al3Li), T-1 (Al2CuLi), S' (Al2CuMg) and core-shell Al-3(Li, Sc, Zr) phases. delta' phases exhibited the relatively lowest thermal stability. The increasing aging temperature led to the greatly enhanced coarsening rate of delta'. It was found that the coarsening of metastable delta' was a diffusion-controlled process and a linear relationship of cube average particle radius (R-3) against aging time t was revealed. The activation energy for the delta' coarsening was estimated to be similar to 98.7 kJ/mol, which was somewhat lower than those in wrought Al-Li alloys. Besides, the activation energy for the growth of T-1 plate was measured to be similar to 95.6 kJ/mol, which was close to that of grain boundary diffusion of Cu in alpha-Al (similar to 105 kJ/mol), indicating that the growth of T-1 should be governed by the diffusion rate of Cu toward T-1 plates. With the successively increased aging temperature and prolonged aging time, the number density and volume fraction of delta' particles were significantly reduced, primarily contributing to the significant strength reduction. The relatively best combination of strength and ductility was achieved in the studied alloy aged at 175 degrees C for 32 h. (C) 2021 Elsevier B.V. All rights reserved.

A Novel Cu-10Zn-1.5Ni-0.34Si Alloy with Excellent Mechanical Property Through Precipitation Hardening

Accelerating Discontinuous Precipitation to Increase Strength by Pre-Deformation in Cu-Ni-Si Alloys

Abnormally high work hardening ability and excellent comprehensive properties of copper alloys due to multiple twins and precipitates

Microstructure and Precipitate's Characterization of the Cu-Ni-Si-P Alloy

Ageing Behavior of Cu-15Ni-8Sn Alloy Prepared by Mechanical Alloying

Microstructure and properties of a novel ultra-high strength, high elasticity and high plasticity Cu–20Ni–20Mn-0.3Nb-0.3Cr-0.1Zr alloy

A novel precipitation‐strengthened conductive copper alloy: Cu‐Hf‐Si alloy

Excellent Mechanical Properties and High Electrical Conductivity of Cu-Co-Si-Ti Alloy Due to Multiple Strengthening

Precipitates-Strengthened Cu-Ni-Si-Fe Conductive Copper Alloy

Investigation of Microstructure and Wear Properties of Precipitates-Strengthened Cu-Ni-Si-Fe Alloy.

A Cu-Ni-Ti Alloy with Excellent Softening Resistance Combined with Considerable Hardness and Electrical Conductivity Obtained by the Traditional Aging Process

An Insight into the Precipitate Evolution and Mechanical Properties of a Novel High-Performance Cast Al-Li-Cu-Mg-X Alloy

Microstructure and Precipitate Evolution in Cu-3.2Ni-0.75Si Alloy Processed by Twin-Roll Strip Casting

On Novel Ni-rich Phase Formed During Aging of an Additively Manufactured Ultra-High Strength CoFeNi Alloy

Effects of Ti Addition on Microstructure, Mechanical Properties and Corrosion Resistance of the Cu-Zn-Ni Alloy

Development of a novel high strength Al-Si-Cu-Ni alloy by combining micro-alloying and squeeze casting

Precipitation in Cu–Ni–Si–Zn Alloy for Lead Frame

Simultaneously enhancing the strength and electrical conductivity of Cu-Ni-Sn alloy through plastic deformation of an intermetallic compound

Precipitation Behaviors and Properties of Solution-Aging Al-Zn-Mg-Cu Alloy Refined with TiN Nanoparticles

Ultra-fine Grained Structure and High-Content Precipitates Enable Ultrastrong Yet Strain-Hardenable Medium-Entropy Alloy

Accelerated discovery of high-performance Cu-Ni-Co-Si alloys through machine learning