Abstract:In this article, an ultra-low-voltage 2.4-GHz radio frequency (RF) receiver front-end architecture targeting the removal of output flicker noise is presented, making it possible to use zero-IF topology for narrow-band communication standards. The trans-impedance amplifier (TIA) is built on the proposed hybrid operational trans-conductance amplifier (OTA) with a switched-capacitor (SC) amplifier as the first gain stage and an active primary–secondary amplifier as the second gain stage, achieving an imperceptible flicker-noise corner frequency. With the SC gain stage, the interstage common-mode voltage can be set to 0 V, which reduces the minimum supply voltage to 0.5 V. As another benefit, dc offset compensation (DCOC) is performed inherently in the interstage sampling and coupling process. Fabricated in 28-nm RF CMOS process, the front-end prototype, including an on-chip matching inductor, occupies a die area of 0.8 mm $^{2}$ . Operating in the Industrial Scientific Medical (ISM) frequency band of 2.4 GHz with 1-MHz IF bandwidth, the front end provides a 36–40-dB conversion gain, an 11.5-dBm OIP3, and a flicker-noise corner frequency less than 10 kHz with the supply voltage ranging from 0.5 to 0.6 V. The RF impedance matching network provides passive voltage gain before the low-noise trans-conductance amplifier (LNTA), achieving a 4.5-dB noise figure (NF) with 0.8-mA biasing current in the $g_m$ stage. With the ultra-low supply voltage and the passive IF gain stage, the power consumption of the proposed front end is only 610 $mu $ W under a 0.53-V supply voltage.

A Chopping Switched-Capacitor RF Receiver With Integrated Blocker Detection.

A chopping switched-capacitor RF receiver with integrated blocker detection, +31dBm OB-IIP3, and +15dBm OB-B1dB.

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A Switched-Capacitor RF Front End With Embedded Programmable High-Order Filtering.

A Switched-Capacitor Rf Front End with Embedded Programmable High Order Filtering and A+15dbm Ob-B1db

Temporally-controlled Switchable Microwave Rasorbers

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A 100mhz-2ghz Wireless Receiver In 40-Nm Cmos For Software-Defined Radio

A 0.4-6 GHz Blocker-Tolerant Receiver in 65 Nm CMOS with Bandwidth-Extended Technologies for Future V2X Applications

Photonic Radiofrequency Receiver Utilizing a Phase Modulator and a Tunable Single Sideband Optoelectronic Oscillator

A 0.18 Um Cmos Programmable Interference Canceller For Cognitive Radio Front-End

Millimeter-Wave Receiver With Non-Uniform Time-Approximation Filter

A 0.5-4Ghz Full-Duplex Receiver with Multi-Domain Self-Interference Cancellation Using Capacitor Stacking Based Second-Order Delay Cells in RF Canceller

Design of Switchable Frequency-Selective Rasorber with A-R-A-T or A-T-A-R Operating Modes

A Wideband Full-Duplex Receiver with Multi-Domain Self-Interference Cancellation Based on Capacitor Stacking Delay and Delay Compensation in Cancellers

An Ultra-Low-Voltage 2.4-GHz Flicker-Noise-Free RF Receiver Front End Based on Switched-Capacitor Hybrid TIA With 4.5-dB NF and 11.5-dBm OIP3

A Cmos Passive Mixer-First Receiver Front-End for Uhf Rfid Reader

A Blocker-Tolerant RF Front End with Harmonic-Rejecting $N$ -Path Filter

A 0.1–4 GHz SDR receiver with reconfigurable 10–100 MHz signal bandwidth in 65 nm CMOS

An area-efficient digitally-assisted DC canceling loop for high sensitivity UHF RFID receiver

A 253- $\mu $ W 2.4-Ghz SAW-Less Mixer-First Uncertain-IF Receiver with Blocker Tolerant for Long-Distance Ultralow-Power IoT