Abstract:This paper presents a 0.2 similar to 3.8-GHz in-band (IB) full-duplex (FD) mixer-first receiver based on a vector self-interference (SI) canceller. To ensure the wideband orthogonality of the reconstructed SI signal while minimizing the noise figure (NF) degradation in FD mode, a low insertion loss two-stage polyphase filter (PPF) with a lacking resistance and capacitance (LRC) structure is used in the SI canceller. A 6-bits passive capacitor digital to analog converter (C-DAC) attenuator not only realizes the high-precision amplitude adjustment of the reconstructed SI signal but also avoids the linearity limitation of the back-end modules of the canceller and reduces the noise contribution of the front-end modules at the canceller output. A four-phase mixer-first receiver with enhanced out-of-band (OOB) interference suppression is designed to provide sufficient linearity to reduce the SI-induced nonlinear distortion. As a proof of concept, a prototype FD receiver is fabricated in CMOS 65 nm technology and measured in chip-on-board (COB) package. Measurement results show that it can operate in the frequency range of 0.2 similar to 3.8-GHz with more than 25 dB SIC amount for 10 MHz bandwidth (BW) 64-QAM modulated signals in fixed (30 dB) channel attenuation test setup. The receiver achieves OOB input-referred third-order intercept point (OOB-IIP3) of +24 dBm and OOB input-referred second-order intercept point (OOB-IIP2) of +82 dBm at 1-GHz local oscillator (LO) frequency. In FD mode, the NF degradation is <= 1.5 dB. The effective IB-IIP3 and effective IB-IIP2 are enhanced by 15 dB and 28 dB, respectively. The power consumption of entire FD receiver including the SI canceller is less than 44 mW. The active chip area is 0.55 mm(2).

A chopping switched-capacitor RF receiver with integrated blocker detection, +31dBm OB-IIP3, and +15dBm OB-B1dB.

A Chopping Switched-Capacitor RF Receiver With Integrated Blocker Detection.

A Switched-Capacitor Rf Front End with Embedded Programmable High Order Filtering and A+15dbm Ob-B1db

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A CMOS 1.3-1.7GHz Q-Enhanced LC Band-pass RF Filter with 1.5-67% Tunable Fractional Bandwidth

A Switched-Capacitor RF Front End With Embedded Programmable High-Order Filtering.

A 0.4-6 GHz Blocker-Tolerant Receiver in 65 Nm CMOS with Bandwidth-Extended Technologies for Future V2X Applications

Photonic Radiofrequency Receiver Utilizing a Phase Modulator and a Tunable Single Sideband Optoelectronic Oscillator

A blocker-tolerant RF front end with harmonic-rejecting N-path filtering

A Blocker-Tolerant RF Front End with Harmonic-Rejecting $N$ -Path Filter

A 253- $\mu $ W 2.4-Ghz SAW-Less Mixer-First Uncertain-IF Receiver with Blocker Tolerant for Long-Distance Ultralow-Power IoT

A 0.1–1.5 GHz Harmonic Rejection Receiver Front-End with Phase Ambiguity Correction, Vector Gain Calibration and Blocker-Resilient TIA

A Baseband-Noise-Cancelling Mixer-First CMOS Receiver Frontend Attaining 220 MHz IF Bandwidth With Positive-Capacitive-Feedback TIA

A 0.1–4 GHz SDR receiver with reconfigurable 10–100 MHz signal bandwidth in 65 nm CMOS

An Ultra-Low-Voltage 2.4-GHz Flicker-Noise-Free RF Receiver Front End Based on Switched-Capacitor Hybrid TIA With 4.5-dB NF and 11.5-dBm OIP3

A Low Power Direct Conversion Receiver RF Front-End with High In-Band IIP2/IIP3 and Low 1/f Noise

A COMPACT X-BAND RECEIVER FRONT-END MODULE BASED ON LOW TEMPERATURE CO-FIRED CERAMIC TECHNOLOGY

A+21.2 Dbm Out-Of-Band Iip3 0.2-3ghz Rf Front-End Using Impedance Translation Technique

A 0.2~3.8-Ghz Full-Duplex Receiver with More Than 25 Db Self-Interference Cancellation Using a C-DAC-Based Vector Canceller.