Abstract:Wake-up receivers (WuRXs) help to significantly reduce the average power of the Internet of the Things (loT) hardware systems. To lower the “asleep” power in the idle state, the WuRX structures based on non-standard protocols have been widely studied in prior researches, which can realize a high sensitivity [1] or low power [2]. Compared to the non-standard receivers, there are more design challenges in the standard-compliant WuRXs. For example, a BLE-compliant WuRX operating in the congested 2.4GHz band should be able to handle potentially large interferers including adjacent-channel tone and image, as well as realize a high sensitivity for long-reach access. Therefore, there have been several conventional solutions for the interference-resilient BLE-compliant WuRXs: 1) Single-path down-conversion WuRXs. The interference is handled by an RF filter [3] or a low-noise LO [4] (Fig. 1, top). The WuRX in [3] utilized an FBAR filter to reject the interference from the adjacent channel, resulting in a signal-to-interference ratio (SIR) of −6dB@2MHz, where the loss of FBAR filter degraded the sensitivity to −85dBm. An LC oscillator based LO was adopted in [4] to suppress the adjacent-channel interference by −10dB, but it's at the penalty of 1.2mW power. 2) I/Q-path down-conversion WuRXs. A Hartley WuRX was designed in [5] to reject both 2MHz adjacent-channel interference and image (Fig. 1, middle), as well as improve the sensitivity to −92dBm, while the I/Q downconverters and LO generators dominated the total power consumption. Although the WuRX power was reduced to 352μW by the edge combiner based I/O LO generation, the SIR was limited to −12.5dB due to the spurs and noise accompanying the LO signal. As a result, it's difficult for the conventional WuRX structures to realize both a high SIR and low power consumption.

A 253- $\mu $ W 2.4-Ghz SAW-Less Mixer-First Uncertain-IF Receiver with Blocker Tolerant for Long-Distance Ultralow-Power IoT

A 0.6V 32.5mw Highly Integrated Receiver for 2.4ghz ISM-Band Applications

20 . 6 A 0 . 6 V 32 . 5 mW Highly Integrated Receiver for 2 . 4 GHz ISM-Band Applications

A 0.6-V Zero-IF/Low-IF Receiver with Integrated Fractional-N Synthesizer for 2.4-Ghz ISM-Band Applications.

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A 0.1-1.9 GHz 65 Nm CMOS Variable-Gain Mixer-First Receiver with DSA and Noise-Shaping TIA

A 11 Mw 2.4 GHz 0.18 Μm CMOS Transceivers for Wireless Sensor Networks

A CMOS Low Power K-band FMCW Radar Transceiver Front-End for AIOT Application

A Low Power Impedance Transparent Receiver with Linearity Enhancement Technique for IoT Applications.

A 55 μ W 2.4 GHz wake-up receiver with offset-based peak detection achieving −90dBm sensitivity for IoT applications

A 55uW 2.4GHz wake-up receiver with offset-based peak detection achieving −90dBm sensitivity for IoT applications

An Interference-Resilient 120-Degree-apart Pseudo-I/Q BLE-Compliant Wake-Up Receiver Achieving-21dB SIR,-94dBm Sensitivity, and 4-D Wake-Up Signature

An 89 Μw MICS/ISM Band Receiver for Ultra-Low-power Applications.

A 2.4 GHz 2.9 Mw Zigbee RF Receiver with Current-Reusing and Function-Reused Mixing Techniques

A 0.13&#x03bc;m CMOS UWB Receiver Front-End Using Passive Mixer

A Low Power SAW-less 2.4-Ghz Receiver with an LC Matched Series N-path Filter.

A 0.8V, 152 μ W, 433 MHz Mixer-First Receiver with a Self-Adjusted Frequency Tracking Loop

A 2.85mm 2 RF Transceiver in 40nm CMOS for IoT Micro-Hub Applications

A Low-Power, Compact, 0.1–5.5-Ghz, 40-Dbm IB OIP3 LNTA-First Receiver for SDR

A 110pj/bit Star- 16QAM 915mhz Band Ultra-Low Power Receiver Based on Polar Architecture

A Low Power 3–5 GHz CMOS UWB Receiver Front-End