Abstract:This study proposes a broadband complementary metal-oxide semiconductor (CMOS) low-noise amplifier (LNA) with intrinsic band-selective out-of-band (OB) blocker rejection capabilities. The proposed LNA design utilizes a differential four-phase N-path filter as the amplifier load to offer a substantial total load impedance difference between the in-band (IB) and OB frequency bands. This ensures that the LNA design securely accomplishes a high-quality-factor frequency selectivity response with lower radio frequency signal losses and its OB rejection performance is maintained against process, voltage, and temperature variations, compared with the case of using the N-path filter as a signal path. To validate its blocker-tolerable performance, the designed LNA was fabricated using a 65-nm CMOS technology and was primarily characterized in the frequency division duplexing bands of the long-term evolution and fifth-generation new radio standards, spanning from 1.7 to 2.7 GHz. The implemented design consistently achieved a transmitter leakage rejection greater than 17 dB across all target frequency bands from several samples. Furthermore, the design attained IB voltage gains greater than 36.4 dB and 40.4 dB, noise figures (NFs) of 1.78 dB and 1.5 dB, OB input 1-dB compression point greater than –27.0 dBm and –26.7 dBm, and full-/half-duplexing OB input-referred third-order intercept points greater than 4.1/3.8 dBm and 4.8/5.0 dBm at the mid- and high-bands, respectively. The OB-induced NF degradation was maintained at less than 0.7 dB. A total bias current of 37.7 mA was required with a nominal supply voltage of 1.2 V. The occupied active area of the implemented design was approximately 0.77 mm2, excluding the bonding pads and input/output cells.

A blocker-tolerant RF front end with harmonic-rejecting N-path filtering

A Blocker-Tolerant RF Front End with Harmonic-Rejecting $N$ -Path Filter

A 0.5&#x2013;2 GHz High Frequency Selectivity RF Front-End with Series N-path Filter

A Low Power 0.4-1 Ghz Receiver Front-End with an Enhanced Third-Order-Harmonic-Rejecting Series N-Path Filter

A High-Linearity 7–9-Ghz Receiver Front End with Strength-Oriented Nonlinearity Cancellation

A 0.1–1.5 GHz Harmonic Rejection Receiver Front-End with Phase Ambiguity Correction, Vector Gain Calibration and Blocker-Resilient TIA

A Switched-Capacitor Rf Front End with Embedded Programmable High Order Filtering and A+15dbm Ob-B1db

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A 5th order 0.8/2.4 GHz programmable active band pass filter for power DAC applications

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A Sub-GHz Low-Power Receiver Employing Resistive-Feedback-Tuned LNA with 2.1-Db NF and 106-Db Gain Tuning Range

A 100M–1.5 GHz harmonic-rejection SDR receiver front-end

A 0.1–1.5GHz harmonic rejection receiver front-end with hybrid 8 phase LO generator, phase ambiguity correction and vector gain calibration

Blocker-Tolerant Broadband CMOS Low-Noise Amplifier Employing N-Path Filter-Based Load

A SAW-less 0.5–2.5 GHz receiver front-end with 80 dB 3rd order harmonic rejection ratio

An N-Path Filter Design Methodology With Harmonic Rejection, Power Reduction, Foldback Elimination, and Spectrum Shaping

Hybrid Integration of BAW Resonators with an On-Chip Inductor to Improve the Stopband Rejection of the N78 Band Filter

A+21.2 Dbm Out-Of-Band Iip3 0.2-3ghz Rf Front-End Using Impedance Translation Technique

A 22.9–38.2-Ghz Dual-Path Noise-Canceling LNA with 2.65–4.62-Db NF in 28-Nm CMOS

An Interference-Robust Reconfigurable Receiver with Automatic Frequency-Calibrated LNA in 65-Nm CMOS

A chopping switched-capacitor RF receiver with integrated blocker detection, +31dBm OB-IIP3, and +15dBm OB-B1dB.