Abstract:A new selective catalytic reduction (SCR) system for captive power plants in the petrochemical industry was analyzed. The key components suitable for the target SCR system were obtained using computational fluid dynamics (CFD) numerical simulation combined with a cold physical model. The structural characteristics of the SCR system were studied, and corresponding design schemes were obtained for the key components, such as the guide plate, the ammonia injection grid (AIG), the static mixer, and the rectifier grille. The distributions of the flue gas velocity and the NH3 concentration within the flue cross-section in front of the first layer catalyst were studied in detail. Synchronously, the pressure loss and the temperature reduction characteristics in the SCR system were also considered. CFD results showed that the average standard deviation of the flue gas velocity was about 11.61%, and the average standard deviation of the NH3 concentration distribution could reach about 3.79% under the five operating conditions. It could be concluded that the uniformity of the flue gas velocity and the NH3 concentration distribution within the above flue cross-section was guaranteed by comparing to the design standard of 15% and 5%, respectively. It was further found that the maximum pressure loss between the inlet and the first layer catalyst was about 106.64 Pa, and the temperature reduction characteristic of the entire SCR system could be maintained within ±0.01 °C, which indicated that no extreme adverse effect arose due to the introduce of the key components. The cold physical model experiment was accordingly conducted to verify the reliability of the above CFD results. The cold physical model experiment results showed that the average standard deviation of flue gas velocity was about 8.82%, and the average standard deviation of NH3 concentration distribution could reach about 4.21%. The maximum biases for the standard deviations of the flue gas velocity and the NH3 concentration distribution were approximately 4.83% and 1.18% under the five operating conditions. Based on the good agreement of the research results via the two different methods, the designed key components of a new SCR system could be confirmed to be feasible, which would benefit the deNOx performance of the SCR system.

Selective Catalytic Reduction (Scr) Modeling Using Parallel Way Of Identification

Model Predictive Control Case Study: Selective Catalytic Reduction (scr) System in Coal-Fired Power Plant

Optimizing Flow Field in an SCR System of a 600 MW Power Plant: Effects of Static Mixer Alignment Style

Modeling and Simulation of Commercial Catalytic Reformers

A temporal discretization and spatial integration SCR model with dual temperature-related parameters

Integrated Gas and Solid Model to Determine the Flow Performance in the SCR Reactor

Design and Verification of Key Components of a New Selective Catalytic Reduction System in a Petrochemical Captive Power Plant

Investigation on the applicability of parameters identification of marine diesel engine SCR kinetic model based on Discrete-Grid algorithm

Development and verification of model predictive control strategy for selective catalytic reduction with rapid prototyping

MODEL TEST AND NUMERICAL ANALYSIS OF FLOW FIELD IN SCR DENITRIFICATION SYSTEM IN SECOND-PHASE PROJECT OF SANHE POWER PLANT

Full-Scale Numerical Investigation of a Selective Noncatalytic Reduction (SNCR) System in a 100 MW Utility Boiler with Complex Chemistry and Decoupling Approach

Multi‐model predictive control of SCR flue gas denitrification system in coal‐fired power plant based on kernel fuzzy c‐means clustering and integrated model

Enhancement of SCR denitrification control strategy considering fluegas temperature fluctuation: Fundamental principle and performance evaluation

Investigating the Optimization Design of Internal Flow Fields Using a Selective Catalytic Reduction Device and Computational Fluid Dynamics

Closed-Loop Control Strategy and State Estimator for Diesel Engine SCR After-Treatment System

Evaluation system for testing performance of selective catalytic reduction (SCR) denitration catalyst

Accelerated Identification of High-Performance Catalysts for Low-Temperature NH3-SCR by Machine Learning

Adaptive Internal Model Control of SCR Denitration System Based on Multi-Objective Optimization

Optimization Analysis of Various Parameters Based on Response Surface Methodology for Enhancing NOx Catalytic Reduction Performance of Urea Selective Catalytic Reduction on Cu-ZSM-13 Catalyst

Large eddy simulation of hydrodynamics and deNOx process in a coal-fired power plant SCR system

Application of an Improved State Feedback Control in the Selective Catalytic Reduction Denitrification Systems of Coal Power Units Under Variable Load Conditions