Abstract:The fabrication art of the membrane electrode assembly (MEA) in a proton-exchange membrane (PEM) fuel cell strongly correlates to the cell performance. It has been recognized that defects, for example, high interfacial resistance between the catalyst layers (CLs) and the membrane or cracks in the CLs, may occur during the MEA manufacturing process. These defects could greatly influence the electrochemical performance of the fuel cell. To eliminate those defects and improve the cell performance, in this study, a novel fabrication approach of the MEA for PEM fuel cells is developed. With this method, the Nafion ionomer, employed as a PEM, is directly coated onto both the cathode and anode CLs. As a result, not only an excellent interfacial connection between the PEM and CLs is achieved with a low interfacial resistance, but also cracks are eliminated due to Nafion ionomer penetration into the cracks, forming hydrophilic channels with ionic conduction. Those ionic conduction channels improve the water management, lower the mass transport loss, and facilitate the proton transfer, thus maximizing the three-phase boundary and enhancing the utilization of Pt/C catalysts. By adding an expanded polytetrafluoroethylene film, a favorable mechanical property of the MEA is also achieved. This novel MEA exhibits excellent cell performance under low humidity conditions. Under the H<sub>2</sub>/air operation, the cell performance reaches a high maximum power density of 1.35 W cm<sup>–2</sup>.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acssuschemeng.0c02386?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acssuschemeng.0c02386</a>.SEM images, photographs of MEAs and fitted impedance parameters for the MEAs (<a class="ext-link" href="/doi/suppl/10.1021/acssuschemeng.0c02386/suppl_file/sc0c02386_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Fabrication of PMMA-based Mini-Direct Methanol Fuel Cell for Portable Devices

Design and Fabrication of a Polymer-Based Micro Direct Methanol Fuel Cell

Fabrication of Micro Direct Methanol Fuel Cell Based on ME MS Technologies

Design, Fabrication and Testing of a Silicon-Based Air-Breathing Micro Direct Methanol Fuel Cell

A Micro Direct Methanol Fuel Cell Using PDMS Assembly Technology

Miniaturized silicon-based direct methanol fuel cell

Design and Fabrication of Fuel-Self-Propelled Reaction Device for Passive Micro Direct Methanol Fuel Cell Anodes

Design, Optimization and Microfabrication of a Micro-Direct Methanol Fuel Cell with Microblocks in Anode Structure

A Novel Assembly Method for a Micro Direct Methanol Fuel Cell Using Multi-Layer Bonding Technique

Nano porous silicon membrane with channels for micro direct methanol fuel cells

Development of MEMS-based direct methanol fuel cell with high power density using nanoimprint technology

A Monolithic Integrated Micro Direct Methanol Fuel Cell Based on Sulfo Functionalized Porous Silicon

Development of Integrated Thermally Autonomous Reformed Methanol-Proton Exchange Membrane Fuel Cell System

Effects Of The Nanoimprint Pattern On The Performance Of A Mems-Based Micro Direct Methanol Fuel Cell

Performance Enhancement of Polymer Electrolyte Membrane with Nano-Calcium Carbonate Prepared by Mechanochemical for Direct Methanol Fuel Cell Applications

An Air-Breathing Micro Direct Methanol Fuel Cell with 3D KOH-Etched Cathode Structure

Mechanically Robust and Highly Methanol-Resistant Sulfonated Poly(ether Ether Ketone)/poly(vinylidene Fluoride) Nanofiber Composite Membranes for Direct Methanol Fuel Cells

A micro-direct methanol fuel cell stack with optimized design and microfabrication

A Novel Approach to Fabricate Membrane Electrode Assembly by Directly Coating the Nafion Ionomer on Catalyst Layers for Proton-Exchange Membrane Fuel Cells

Nanoimprint of Proton Exchange Membrane for MEMS-based Fuel Cell Application

Optimization of Membrane Electrode Assembly in Air-Breathing Direct Methanol Fuel Cell