Abstract:TiAl alloy is one of the most attractive candidates for a new generation of high-temperature structural materials and has broad application prospects in the aerospace field. As a typical intermetallic material, TiAl is inevitably difficult to process using conventional methods. Election beam selective melting (EBSM) is an effective method of addictive manufacturing to prepare TiAl alloy with a complex structure. However, the microstructure of TiAl alloy formed using EBSM often contains defects such as pores, which seriously reduces the mechanical properties of the material. In this work, the effects of EBSM and post-processing procedures on the microstructure and mechanical properties of Ti-48Al-2Cr-2Nb alloy were studied. The results show that the microstructure of Ti-48Al-2Cr-2Nb alloy formed using the EBSM process was dense and composed of equiaxed γ-phase and double-phase regions. A large number of dislocations that formed due to thermal stress were clearly observed inside the Ti-48Al-2Cr-2Nb alloy. When the EBSM process parameters were 13.5 mA, 4.0 m/s, and 40.50 J/mm3, as the current intensity increased, the Al content decreased, the content of α2 phase increased, and the microstructure of the material was coarse. The results of the tensile test fracture morphology indicate that the Ti-48Al-2Cr-2Nb alloy exhibited brittle fracture during tensile deformation, lacking the typical yield deformation of metal materials. As the energy density of the EBSM process increased, the mechanical properties of the Ti-48Al-2Cr-2Nb alloy first increased and then decreased. The samples prepared with an energy density of 34.50~40.50 J/mm3 had excellent mechanical properties, of which the maximum tensile strength and maximum elongation reached 643 MPa and 2.09%, respectively. The phase composition of the Ti-48Al-2Cr-2Nb alloy after hot isostatic pressing (HIP) treatment remained unchanged from the EBSM samples, but there was a slight difference in content. There was an increase in the amount of γ phase and a decrease in B2 phase, accompanied by the generation of a massive γ phase after HIP treatment. Moreover, the number of dislocations inside the material increased. The Ti-48Al-2Cr-2Nb alloy after HIP treatment exhibited obvious plastic deformation characteristics, with a tensile strength of 679 MPa and elongation of 2.5%. A heat treatment of 900 °C/5 h was performed on the Ti-48Al-2Cr-2Nb alloy after HIP. The dislocation density of the Ti-48Al-2Cr-2Nb alloy decreased, and the B2 phase transformed from massive to lamellar.

A High-Nb TiAl Alloy with Highly Refined Microstructure and Excellent Mechanical Properties Fabricated by Electromagnetic Continuous Casting

Microstructure refinement and improvement of mechanical properties of Ti46Al8Nb0.9B alloys by electromagnetic cold crucible continuous solidification

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

High-throughput analysis of Al and Nb effects on mechanical behaviour of TiAl alloys using electromagnetic cold crucible continuous casting

Ti-48Al-2Cr-2Nb alloys prepared by electron beam selective melting additive manufacturing: microstructural and tensile properties

TiAl Alloy Fabricated Using Election Beam Selective Melting: Process, Microstructure, and Tensile Performance

Microstructure Transformation of a Refined High Nb Containing TiAl Alloy

Evolution of microstructure and mechanical properties in the molten pool of γ-TiAl alloy synthesized in situ by dual-wire-fed electron beam directed energy deposition.

Microstructures Of Components Synthesized Via Electron Beam Selective Melting Using Blended Pre-Alloyed Powders Of Ti6al4v And Ti45al7nb

Peritectic Solidification Kinetics and Mechanical Property Enhancement in a Rapidly Solidified Ti–48 at% Al–8 at% Nb Alloy via Hierarchical Twin Microstructure

A new insight into high-strength Ti 62 Nb 12.2 Fe 13.6 Co 6.4 Al 5.8 alloys with bimodal microstructure fabricated by semi-solid sintering

Hierarchical microstructure of a titanium alloy fabricated by electron beam selective melting

The microstructural evolution and enhanced mechanical properties of in-situ Ti(C, N)-reinforced CoCrFeNiTi high-entropy alloy composites fabricated via mechanical alloying and spark plasma sintering

Microstructure evolution and enhanced mechanical properties in Al-Mn alloy reinforced by B-doped TiC particles

Design, microstructure and thermal stability of a novel heat-resistant Al-Fe-Ni alloy manufactured by selective laser melting

A new α + β Ti-alloy with refined microstructures and enhanced mechanical properties in the as-cast state

Effect of Electromagnetic Power on the Microstructure and Properties of 2219 Aluminum Alloy in Electromagnetic Continuous Casting Technology

Microstructure Evolution and Mechanical Properties' Improvement of NiAl–Cr(Mo)–Hf Eutectic Alloy During Suction Casting and Subsequent HIP Treatment

Regulation on Microstructures and Properties of Hypereutectic Al–3.5Fe–2.5Ni Alloy by Controlled Diffusion Solidification

Microstructure and mechanical properties of a Cu-Fe-Nb alloy with a high product of the strength times the elongation