Abstract:<p>A multiple principal elements CuAl10Fe5Ni5Mn1.2 alloy is widely used in the bearing bracket of high speed railway, nuclear power and marine engineering. In traditional metal materials, the evolution of strength and elongation are mutually inconsistent. The multiple principal elements CuAl10Fe5Ni5Mn1.2(wt%) alloy shows the simultaneous improvement of strength and toughness. The present work has systematically studied the strengthening and plasticity behaviors of CuAl10Fe5Ni5Mn1.2(wt%) alloy under complex stirring. The mechanisms responsible for both increasing its strength and plasticity were clarified. It is found that the properties of novel Al10Fe5Ni5Mn1.2 (wt%) alloy are better than other aluminum bronze alloys. Its Rm is 729 MPa, A<sub>5.65</sub> is 16% and yield strength (Rp0.2) is 382 MPa. K phases with nano structures distribute in the grains boundaries complete boundaries strengthening. Schmid factor for the basal slip system is from 0.3 to 0.5, which could largely contribute to grain boundary migration and grain rotation. Twinning deformation is initiated and it can open the low angle grain boundaries (LAGBs) and media angle grain boundaries (MAGBs), so the proper combination of strain hardening and plastic deformation enables CuAl10Fe5Ni5Mn1.2 wt% to undergo uniform deformation with micro-nano structures, result in increasing the toughness. The solid solution forms atom scale strengthening. Nano-structures and micron K phase form nano-micro scale strengthening, respectively. Multi-scales strengthening and twinning deformation opening the LAGBs and MAGBs, resulting in increasing both strength and plasticity on the novel CuAl10Fe5Ni5Mn1.2 wt% alloy.</p>

Microstructure and mechanical properties of a Cu-Fe-Nb alloy with a high product of the strength times the elongation

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Microstructure and properties of a novel ultra-high strength, high elasticity and high plasticity Cu–20Ni–20Mn-0.3Nb-0.3Cr-0.1Zr alloy

Break the strength and ductility trade-off in novel NbC reinforced Fe40.5(CoCr)25Mn17.5Ni10Si5 high entropy alloy

Effect of Nb content on mechanical reinforcement of the Cu-10Fe composites

Effect of Microalloying Rare-Earth Nd on Microstructure Evolution and Mechanical Property of Cu Alloy

Enhanced Mechanical Properties in a Low-Carbon Ultrafine Grain Steel by Niobium Addition

Microstructure evolution and quantitative analysis of mechanical properties of cold-rolled low carbon niobium steel

Microstructures and mechanical properties of in-situ FeCrNiCu high entropy alloy matrix composites reinforced with NbC particles

Microstructure Evolution and Tensile Property of a CuMnFeCoNi High-Entropy Alloy During Thermomechanical Treatment

Mechanical behaviors of novel multiple principal elements CuAl10Fe5Ni5Mn1.2 wt% with micro-nano structures

Microstructure and properties of a novel cost-effective FeNi-based eutectic high entropy alloys

Microstructural evolution and properties of a Cu-Fe-Mn-P alloys with high strength and high conductivity

Microstructure and Tensile Properties of Al0.5CoCrCuFeNi Alloys Produced by Simple Rolling and Annealing

Influences of Fe Content and Cold Drawing Strain on the Microstructure and Properties of Powder Metallurgy Cu-Fe Alloy Wire

High tensile ductility in a nanostructured metal

Influence of cold rolling and annealing on the microstructure, mechanical properties, and electrical conductivity of an artificial microcomposite Cu-18% Nb alloy

Mechanical properties and fracture mechanism of as-cast MnFeCoCuNi high-entropy alloys

Mechanical properties and microstructural evolution of a novel (FeCoNi)86.93Al6.17Ti6.9 medium entropy alloy fabricated via powder metallurgy technique

Mechanical Behaviors of Chromium- or Niobium-Modified Ni47.5Al25Fe27.5 Alloy at Elevated Temperature

Effects of Niobium Addition on Dynamic Mechanical Behavior and Fracture Properties of Iron-Aluminide-Based Alloys