Abstract:TiAl alloy is one of the most attractive candidates for a new generation of high-temperature structural materials and has broad application prospects in the aerospace field. As a typical intermetallic material, TiAl is inevitably difficult to process using conventional methods. Election beam selective melting (EBSM) is an effective method of addictive manufacturing to prepare TiAl alloy with a complex structure. However, the microstructure of TiAl alloy formed using EBSM often contains defects such as pores, which seriously reduces the mechanical properties of the material. In this work, the effects of EBSM and post-processing procedures on the microstructure and mechanical properties of Ti-48Al-2Cr-2Nb alloy were studied. The results show that the microstructure of Ti-48Al-2Cr-2Nb alloy formed using the EBSM process was dense and composed of equiaxed γ-phase and double-phase regions. A large number of dislocations that formed due to thermal stress were clearly observed inside the Ti-48Al-2Cr-2Nb alloy. When the EBSM process parameters were 13.5 mA, 4.0 m/s, and 40.50 J/mm3, as the current intensity increased, the Al content decreased, the content of α2 phase increased, and the microstructure of the material was coarse. The results of the tensile test fracture morphology indicate that the Ti-48Al-2Cr-2Nb alloy exhibited brittle fracture during tensile deformation, lacking the typical yield deformation of metal materials. As the energy density of the EBSM process increased, the mechanical properties of the Ti-48Al-2Cr-2Nb alloy first increased and then decreased. The samples prepared with an energy density of 34.50~40.50 J/mm3 had excellent mechanical properties, of which the maximum tensile strength and maximum elongation reached 643 MPa and 2.09%, respectively. The phase composition of the Ti-48Al-2Cr-2Nb alloy after hot isostatic pressing (HIP) treatment remained unchanged from the EBSM samples, but there was a slight difference in content. There was an increase in the amount of γ phase and a decrease in B2 phase, accompanied by the generation of a massive γ phase after HIP treatment. Moreover, the number of dislocations inside the material increased. The Ti-48Al-2Cr-2Nb alloy after HIP treatment exhibited obvious plastic deformation characteristics, with a tensile strength of 679 MPa and elongation of 2.5%. A heat treatment of 900 °C/5 h was performed on the Ti-48Al-2Cr-2Nb alloy after HIP. The dislocation density of the Ti-48Al-2Cr-2Nb alloy decreased, and the B2 phase transformed from massive to lamellar.

High-throughput analysis of Al and Nb effects on mechanical behaviour of TiAl alloys using electromagnetic cold crucible continuous casting

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Microstructure refinement and improvement of mechanical properties of Ti46Al8Nb0.9B alloys by electromagnetic cold crucible continuous solidification

TiAl Alloy Fabricated Using Election Beam Selective Melting: Process, Microstructure, and Tensile Performance

Microstructure Evolution and Mechanical Properties of High Nb-TiAl Intermetallic Compounds during Heat Treatment

Microstructural evolution and mechanical properties of a Cr-rich β-solidifying TiAl-based alloy prepared by electromagnetic cold crucible continuous casting

Evolution of microstructure and mechanical properties in the molten pool of γ-TiAl alloy synthesized in situ by dual-wire-fed electron beam directed energy deposition.

Peritectic Solidification Kinetics and Mechanical Property Enhancement in a Rapidly Solidified Ti–48 at% Al–8 at% Nb Alloy via Hierarchical Twin Microstructure

Ti-48Al-2Cr-2Nb alloys prepared by electron beam selective melting additive manufacturing: microstructural and tensile properties

Scalable manufacturing of the Al-based master composites containing TiB 2 and TiC particles and their modification effect on the hot cracking of rapidly solidified Al alloys

Microstructure Evolution and Mechanical Properties' Improvement of NiAl–Cr(Mo)–Hf Eutectic Alloy During Suction Casting and Subsequent HIP Treatment

Calculation of Flow, Heat Transfer and Evaporation During the Electron Beam Cold Hearth Melting of Ti-6Al-4V Alloy

Atomic diffusion and microstructural evolution at the Nb/TiAl heterogenous interfaces during annealing at elevated temperatures

Simulation study on temperature field and microstructure of Ti-6Al-4V alloy round ingot during EBCHM

Microstructure and Mechanical Properties Determined in Compressive Tests of Quasi-Rapidly Solidified NiAl-Cr(Mo)-Hf Eutectic Alloy after Hot Isostatic Pressure and High Temperature Treatments

Effect of Casting Process and Thermal Exposure on Microstructure and Mechanical Properties of Al-Si-Cu-Ni Alloy

Mechanism investigation on high-performance Cu-Cr-Ti alloy via integrated computational materials engineering

Microstructual evolution in Ti-185 alloy prepared using electrostatic levitation and conventional casting techniques

Hierarchical microstructure of a titanium alloy fabricated by electron beam selective melting

Effect of Process Parameters on Microstructure of TiAl Alloy Produced by Electron Beam Selective Melting

A new approach to determine/design the eutectic composition of binary, ternary, and high-entropy alloys using electromagnetic directional crystallization