Abstract:Background: To evaluate the quality of in vitro fenestrations during in situ fenestration (ISF) and investigate the differences between needle and laser puncture in current stent-grafts. Methods: An in vitro study evaluated the damage created by needle ISF on stent-graft fabrics versus laser ISF. Fenestrations were made in 5 different commercially available stent-grafts, including polyester stent-grafts (Relay, Valiant and Hercules) and expanded polytetrafluoroethylene (ePTFE) stent-grafts (TAG and Ankura). Each stent-graft received fenestration by needle and laser separately, followed by gradual dilation (4 mm, 6 mm, 8 mm, and 10 mm sequentially) of noncompliant balloons. Quantitative and qualitative evaluations including fenestration diameter, area, shape and margins were conducted using light microscopy and scanning electron microscope. Results: The primary fenestrations created by needle were slit-like with visible cut-off fibers in polyester stent-grafts and were almost circular with clear margins in ePTFE stent-grafts; those created by laser were squared or elliptical with ragged edges and burned fibers in all the stentgrafts. Fabric debris and toxic particles due to burning of the material were generated during laser-assisted fenestration. The Primary holes in polyester stent-grafts (Relay, Valiant and Hercules) by needle showed smaller area (0.05 mm(2) vs. 0.22 mm(2), 0.52 mm(2) vs. 0.70 mm(2) and 0.28 mm(2) vs. 0.46 mm(2); P < 0.01) and worse shape (0.93 vs. 2.46, 1.17 vs. 2.33 and 0.93 vs. 2.47; P < 0.01) than those by laser, while larger area (0.67 vs.0.43, 0.59 vs.0.45; P < 0.05), better shape (3.93 vs. 2.53, 3.90 vs. 2.93; P < 0.05) and better margin (3.83 vs. 2.47, 3.83 vs. 2.53; P < 0.05) in ePTFE stent-grafts (TAG and Ankrura). After gradual balloon dilation, the final holes showed no evident difference in maximal length, fenestration area, scores of shape and margin between the 2 ways of fenestration (P > 0.05). Ankura stent-graft showed the largest holes with best quality than the others. Conclusions: The primary fenestrations were different between needle and laser puncture, laser induced fabric debris and toxic particles release should be cautiously considered. The final fenestrations were similar after gradual balloon dilation.

Fiber Laser Micromachining of Thin NiTi Tubes for Shape Memory Vascular Stents

Experimental Analysis of In Situ Fenestration of Endovascular Stent-Grafts: Comparison between Needle and Laser Puncture

Optimizing femtosecond laser fabricating strategy of Nitinol hypotube for vascular interventional surgery

High-Performance Self-Expanding NiTi Stents Manufactured by Laser Powder Bed Fusion

Investigations on the interaction of laser parameters for efficient microdrilling of NiTiV smart alloy system

Cutting NiTi with Femtosecond Laser

Fiber laser cutting study on ternary NiTiV shape memory alloy

[Albuminuria in young subjects determined following enlistment and medico-military problems associated with its detection].

Nickel‐Titanium Alloy Laser Micromachining: A Review of Nitinol Laser Processes and Optimization for High‐Speed Laser Cutting

Microscale stress-geometry interactions in an additively manufactured NiTi cardiovascular stent: A synchrotron dual imaging tomography and diffraction study

Mitigation of bio-corrosion characteristics of coronary artery stent by optimising fs-laser micromachining parameters

Shape-Setting of Self-Expanding Nickel–Titanium Laser-Cut and Wire-Braided Stents to Introduce a Helical Ridge

Fiber Laser Cutting of Cu–Zr Added Quaternary NiTi Shape Memory Alloy: Experimental Investigation and Optimization

In-Vitro Investigation on the Tribological Properties of Nickel-Titanium (NiTi) Alloy Used in Braided Vascular Stents

Mechanical and microstructural properties of additively manufactured Ti–6Al–4 V stents with CO2 laser postannealing treatment

Laser powder bed fusion additive manufacturing of NiTi shape memory alloys: A review

A Special Process of 3D Servo Scanning Micro Electro Discharge Machining for Machining Pierced Micro Structures of NiTi Alloy Tube

Optimizing laser parameters and exploring building direction dependence of corrosion behavior in NiTi alloys fabricated by laser powder bed fusion

Micro selective laser melting of NiTi shape memory alloy: Defects, microstructures and thermal/mechanical properties

Corrosion Behavior of NiTi Alloys Fabricate by Selective Laser Melting Subjected to Femtosecond Laser Shock Peening