Abstract:To fabricate complex structures made of nitinol (NiTi), additive manufacturing (AM) has drawn significant interest. However, due to its high microstructural and compositional sensitivities, it is still challenging to fabricate functional NiTi devices via AM. It has been widely reported that evaporation of Ni and formation of precipitation phases during fabrication significantly diverts the expected functional properties. To this date, laser powder bed fusion (LPBF) was the choice among many AM techniques to fabricate NiTi devices but successfully only on a NiTi substrate because of its poor bonding to other substrates (i.e., steel and Ti). Expensive NiTi substrate significantly limits the economic feasibility of fabricating NiTi parts. In this work, a multi-step approach was systematically developed, which enabled printing NiTi on a Ti substrate using a very low laser energy density of 35 J/mm 3 without any visible defect. This printing method avoided the Ni evaporation as well as facilitated fast cooling by avoiding the formation of undesirable precipitation phase during solidification. The phase transformation peaks in differential scanning calorimetry (DSC) data clearly indicated that the printed sample is in austenite (B2) phase at room temperature. In the cyclic compressive test, the samples showed superelasticity with recovery ratios of 73 % and 92 % in the 1st and 10th cycle, respectively, from an imposed strain of 8.04 %. Electron backscatter diffraction (EBSD) analysis proved the presence of major [001] oriented B2 grains along the building direction which was attributed to the shallower melt pool obtained by the low laser energy density scanning. It was also found that higher oxygen level in the printing chamber reduced the austenite finish (A f ) temperature and negatively affected the printability. These results showed the feasibility of LPBF in printing NiTi on a substrate other than nitinol, providing a possible route to reduce the cost of NiTi fabrication via AM with improved superelastic properties.

Cutting NiTi with Femtosecond Laser

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Fiber Laser Cutting of Cu–Zr Added Quaternary NiTi Shape Memory Alloy: Experimental Investigation and Optimization

Corrosion Behavior of NiTi Alloys Fabricate by Selective Laser Melting Subjected to Femtosecond Laser Shock Peening

Selective Laser Melting of Pre-Alloyed NiTi Powder: Single-Track Study and FE Modeling with Heat Source Calibration

Laser Annealing of Amorphous Ni-Ti Shape Memory Alloy Thin Films

Microstructure and Mechanical Properties of NiTi Shape Memory Alloys by Laser Engineered Net Shaping

Microstructure and Phase Transformation Temperature of NiTiNb Shape Memory Alloy Prepared by Laser Solid Forming Using Mixed Powder

Investigations on the interaction of laser parameters for efficient microdrilling of NiTiV smart alloy system

Laser powder bed fusion of nitinol shape memory alloy with superelastic characteristics on Ti substrate

Nickel‐Titanium Alloy Laser Micromachining: A Review of Nitinol Laser Processes and Optimization for High‐Speed Laser Cutting

Achieving Superelasticity in Additively Manufactured Ni-Lean NiTi by Crystallographic Design

Bonding Niti to Glass with Femtosecond Laser Pulses

Laser powder bed fusion additive manufacturing of NiTi shape memory alloys: A review

Laser Polishing of Nickel-Titanium Shape Memory Alloy Produced via Laser Powder Bed Fusion

Achieving superelasticity in additively manufactured NiTi in compression without post-process heat treatment

Aqua jet integrated fiber laser machining of quaternary NiTiCuZr alloy

Laser microwelding as a novel alloying process to fabricate NiTiPtIr high temperature shape memory alloys

Fiber laser cutting study on ternary NiTiV shape memory alloy

Superelastic NiTi Functional Components by High-Precision Laser Powder Bed Fusion Process: The Critical Roles of Energy Density and Minimal Feature Size

Mechanisms of femtosecond laser ablation of Ni3Al: Molecular dynamics study