Abstract:WC-Co cemented carbide has excellent cutting performance, which is a potential tool material. But when it is used as cutting ultra-high strength and high hardness materials, the machining accuracy and service life of the tool are significantly reduced. Graphene is a potential coating material for cemented carbide cutting tools due to its excellent mechanical properties. In this work, molecular dynamics (MD) is used to simulate the deposition of nickel transition layer and high-temperature catalytic growth of graphene in cemented carbide. The Ni and C atomic deposition process and the high temperature annealing process are simulated, and a combination of potential functions is adopted to continuously simulate these two deposition processes. The effect of deposition temperature and the effect of incident energy on the growth of graphene are analyzed. The healing mechanism of nickel-based catalytic defective graphene under high-temperature annealing is explored in detail.The simulation results show that at the deposition temperature of 1100 K, the coverage of graphene is higher and the microstructure is flat. The higher temperature helps to provide enough kinetic energy for carbon atoms to overcome the potential energy barrier of nucleation, thereby promoting the migration and rearrangement of carbon atoms and reducing graphene growth defects. Too high a temperature will lead to continuous accumulation of carbon atoms on the deposited carbon rings, forming a multilayered reticulation and disordered structure, which will cause a low coverage rate of graphene. The increase of incident energy helps to reduce the vacancy defects in the film, but excessive energy leads to poor continuity of the film, agglomeration, the more obvious stacking effect of carbon atoms and the tendency of epitaxial growth. When the incident energy is 1 eV, the surface roughness of the film is lower, and more monolayer graphene can be grown. During annealing at 1100 K, the carbon film dissolves and nucleates simultaneously in the Ni transition layer, and the nickel transition layer catalyzes the repair of defective graphene. The graphene film becomes more uniform, and the number of hexagonal carbon rings increases. Appropriate high-temperature annealing can help to repair and reconstruct defective carbon rings and rearrange carbon chains into rings. Therefore, when the deposition temperature is 1100 K and the incident energy is 1 eV, graphene can be deposited and annealed to grow a high-quality graphene coatings. The simulation results provide the reference for preparing the cemented carbide graphene coated tools. Acta Physica Sinica. 2024 73(23): 238701. Published 2024-12-05

Preparation and Mechanical Properties of Hard Metals Using Graphene As Carbon Source

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Effect of Graphene on the Microstructure and Mechanical Properties of WC-Based Cemented Carbide

Mechanical properties of low-pressure sintered WC-6Co cemented carbide doped with graphene oxide/alumina composite particles

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Effect of graphene on microstructure and properties of Gr/CuCr10 composites

Preparation and characterization of high hard and high tough ultrafine WC ceramics containing hybrid graphene and SiC nanowire

Preparation and Tribological Properties of Graphene-Based Coatings on Tungsten Carbide

A novel approach for in-situ preparation of copper/graphene composite with high hardness and high electrical conductivity

Study on the preparation mechanism of novel WC-Cr2(C, N)-Co nanocomposites

Microstructure and mechanical properties of WC-(Ti,W)C-Co hardmetals fabricated by in-situ carbothermal reduction of oxides and subsequent liquid phase sintering

Mechanical Effects of Carbon Nanotubes-Graphene Reinforced Aluminium Matrix Composites

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Molecular dynamics simulation of effect of nickel transition layer on deposition of carbon atoms and graphene growth on cemented carbide surfaces

Formation Mechanism and Cohesive Energy Analysis of Metal-Coated Graphene Nanocomposites Using In-Situ Co-Reduction Method

Microstructure Evolution and Hardness Improvement of WC-Co Composites Sintered with Fe Substituting Part of Co Binder

A novel approach to fabricate WC reinforced W Cu composites via MSC and infiltration method

Preparation of WC@graphene reinforced titanium diboride‐based composite ceramic materials fabricated via SPS

Preparation and Properties of Ni–W Composite Coatings Reinforced by Graphene Nanoplatelets

Ultra-superior mechanical properties of multilayer graphene nanosheets reinforced carbon-graphite materials

Preparation of low binder WC-Co-Ni cemented carbides with fine WC grains and homogeneous distribution of Co/Ni