Abstract:Highly ordered TiO2 nanotube array electrodes were successfully fabricated by a two-step anodization method on Ti sheet substrates in an electrolyte composed of ammonium fluoride, deionized water, and glycol. The tube wall was smooth, and the average internal and external diameters, wall thickness, and tube length achieved were 80 nm, 90 nm, 10 nm, and 9 μm, respectively. X-ray diffraction and field emission scanning electron microscopy results revealed that the TiO2 nanotube arrays presented an amorphous structure. When calcined at 300 °C, the arrays crystallized into the anatase phase, and the crystallization degree of the oxide layer increased as the temperature rose. Calcinating at 400 °C did not obviously disrupt the porous structure of the highly ordered arrays. However, higher temperature enlarged the diameter of the nanotube array and roughened the tube wall. When the temperature reached 600 °C, the nanotube mouth broke because of the excessive stress, causing the oxide layer’s thinness and nanotube mouth clogging. The photoelectric test showed that the electrode presented obvious photoresponse under 300–400 nm UV excitation (maximized at 360 nm). The degree of crystallization and the micro-structure of the oxide layer can significantly affect the photoelectric properties of the electrode. After calcination at 400 °C, the TiO2 nanotube arrays, with highly ordered tubular structure directly connected to the Ti substrate, can ensure the rapid transportation of photo-induced electrons to the Ti substrate, while the high crystallinity of the arrays can help reduce the defect density of the nanotube and extend the lifetime of the photo-induced carriers. The electrode showed the best photoelectric property, and the photocurrent intensity was maximized (29.6 μA). However, the calcination process with over-temperature resulted in substantial loss of the TiO2 oxide layer, mouth clogging, and a severe decline in the photoelectric properties.

Study on Hydrothermal Synthesis and Performances of Thin Film Barium Titanate Ceramic Nano-tubes

Low Temperature Hydrothermal Synthesis and Performances of Nanotube Patterned Barium Titanates Thin Films

Temperature-dependent differences in wettability and photocatalysis of TiO 2 nanotube arrays thin films

Controllable Hydrothermal Synthesis, Optical and Photocatalytic Properties of TiO2 Nanostructures

Low-temperature synthesis of barium titanate thin films by nanoparticles electrophoretic deposition

Preparation of A Monodispersed Suspension of Barium Titanate Nanoparticles and Electrophoretic Deposition of Thin Films

Synthesis and Properties of Ce3+ Doped Barium Titanate Nanotube Thin Films

Hydrothermal Synthesis Of Thin Films Of Barium Titanate Nanotube Arrays

Synthesis of Thin Films of Barium Titanate and Barium Strontium Titanate Nanotubes on Titanium Substrates

Preparation of Nano-Structured BaTiO3 Thin Film by Electrophoretic Deposition and Its Characterization

Hydrothermal Synthesis of Tetragonal BaTiO3 Nanotube Arrays with High Dielectric Performance

Surface Modification of Ultra-fine Barium Titanate

Structure-tunable Synthesis and Structural Stabilities of the Multilayered Titanate Nanotube Thin Films Grown on Titanium Metal Surface

Microstructural Characterization of BaTiO3 Ceramic Nanoparticles Synthesized by the Hydrothermal Technique

Hydrothermal BaTiO3 Thin Films on Ti‐Covered Silicon: Characterization and Growth Mechanism

Microstructural Characterization of BaTiO<sub>3</sub> Ceramic Nanoparticles Synthesized by the Hydrothermal Technique

Synthesis, Characterization and Electrical Properties of Barium Titanate Films Fabricated by Hydrothermal Method

Fabrication, physical property and microstructural characterization of ferroelectric BaTiO3 nanofilms

Formation of BaTiO3 and PbTiO3 thin films under mild hydrothermal conditions

Study on Fabrication and UV Photoelectric Property of TiO2 Nanotube Array Electrodes.

Preparation of Monodisperse Nanocrystalline Barium Titanate