Abstract:Phase-locked loops (PLLs) are a crucial building block in modern Systems-on-Chip (SoCs), which contain microprocessors, I/O interfaces, memories, power management, and communication systems. Fully synthesizable PLLs [1-2], designed using a pure digital design flow, have been proposed to reduce the design cost and allow easier integration. To achieve high-frequency resolution, PLLs are required to operate in fractional-N mode, in addition to integer-N mode. There are several architectures available [5-6] for realizing fractional-N operation. However, the existing topologies are not well suited for synthesis, as they require a time-to-digital converter (TDC) [3] and a digital-to-time converter (DTC) [4-5]. TDCs and DTCs are vulnerable to layout uncertainty, arising from automatic place and route (P&R), introducing linearity degradation and leading to poor in-band and out-of-band phase noise in PLLs. Injection locking is a promising technique for synthesizable PLLs. Unfortunately, it suffers from large spur caused by a periodic hard refresh, and limited fractional resolution, which is bounded to the inverse of the number of ring oscillator delay stages [6]. This paper describes a fully synthesizable fractional-N PLL with a soft injection-locking technique for smoothing switching and fine fractional resolution, and a cascading topology for suppressing the free-running oscillator phase noise over a wide loop bandwidth.

An Automatic Place-And-Routed Two-Stage Fractional-N Injection-Locked Pll Using Soft Injection

A 1.2ps-jitter fully-synthesizable fully-calibrated fractional-N injection-locked PLL using true arbitrary nonlinearity calibration technique

14.1 A 0.048mm2 3mW synthesizable fractional-N PLL with a soft injection-locking technique

A Fully-Synthesizable Fractional-N Injection-Locked PLL for Digital Clocking with Triangle/Sawtooth Spread-Spectrum Modulation Capability in 5-Nm CMOS

A Low Power Sub-GHz PLL with Optimized Class-C Voltage-controlled Oscillator

Optimized System Design for Fully Integrated Fractional-N Pll

0.2Mw 70Fsrms-Jitter Injection-Locked PLL Using De-Sensitized SSPD-Based Injecting-Time Self-Alignment Achieving -270Db FoM and -66Dbc Reference Spur

A 0.4-Ps-jitter −52-Dbc-spur Synthesizable Injection-Locked PLL with Self-Clocked Nonoverlap Update and Slope-Balanced Subsampling BBPD

An HDL-synthesized Injection-Locked PLL Using LC-based DCO for On-Chip Clock Generation

A Dual-Loop Injection-Locked PLL with All-Digital Background Calibration System for On-Chip Clock Generation

2 GHz sub-harmonically injectin-locked PLL with mixer-based injection timing control in 0.18 μm CMOS technology

A Compact, Low-Power and Low-Jitter Dual-Loop Injection Locked PLL Using All-Digital PVT Calibration

A 0.022mm2 970µw Dual-Loop Injection-Locked PLL with −243db FOM Using Synthesizable All-Digital PVT Calibration Circuits

A 2.6ghz ΔΣ Fractional-N Bang-Bang PLL with FIR-Embedded Injection-Locking Phase-Domain Low-Pass Filter

A Fully Synthesizable All-Digital PLL With Interpolative Phase Coupled Oscillator, Current-Output DAC, and Fine-Resolution Digital Varactor Using Gated Edge Injection Technique

A 56-GHz Fractional-N PLL With 110-fs Jitter

High Performance Injection-Locked PLL Architectures: An Overview

A Fractional-N Sub-Sampling PLL Using a Pipelined Phase-Interpolator with an FoM of -250 Db.

An HDL-synthesized Gated-Edge-injection PLL with a Current Output DAC

An Ultra Low Power Integer-N PLL with a High-Gain Sampling Phase Detector for IOT Applications in 65 nm CMOS

An LC-DCO based synthesizable injection-locked PLL with an FoM of -250.3dB.