Abstract:Phase-locked loops (PLLs) are a crucial building block in modern Systems-on-Chip (SoCs), which contain microprocessors, I/O interfaces, memories, power management, and communication systems. Fully synthesizable PLLs [1-2], designed using a pure digital design flow, have been proposed to reduce the design cost and allow easier integration. To achieve high-frequency resolution, PLLs are required to operate in fractional-N mode, in addition to integer-N mode. There are several architectures available [5-6] for realizing fractional-N operation. However, the existing topologies are not well suited for synthesis, as they require a time-to-digital converter (TDC) [3] and a digital-to-time converter (DTC) [4-5]. TDCs and DTCs are vulnerable to layout uncertainty, arising from automatic place and route (P&R), introducing linearity degradation and leading to poor in-band and out-of-band phase noise in PLLs. Injection locking is a promising technique for synthesizable PLLs. Unfortunately, it suffers from large spur caused by a periodic hard refresh, and limited fractional resolution, which is bounded to the inverse of the number of ring oscillator delay stages [6]. This paper describes a fully synthesizable fractional-N PLL with a soft injection-locking technique for smoothing switching and fine fractional resolution, and a cascading topology for suppressing the free-running oscillator phase noise over a wide loop bandwidth.

A Fully Synthesizable All-Digital PLL With Interpolative Phase Coupled Oscillator, Current-Output DAC, and Fine-Resolution Digital Varactor Using Gated Edge Injection Technique

15.1 A 0.0066mm2 780μw Fully Synthesizable PLL with a Current-Output DAC and an Interpolative Phase-Coupled Oscillator Using Edge-Injection Technique

A Low Power Sub-GHz PLL with Optimized Class-C Voltage-controlled Oscillator

An HDL-synthesized Gated-Edge-injection PLL with a Current Output DAC

A 0.8 V Low Power Low Phase-Noise Pll

A Fully Synthesizable Injection-Locked Pll with Feedback Current Output Dac in 28 Nm Fdsoi

An LC-DCO based synthesizable injection-locked PLL with an FoM of -250.3dB.

14.1 A 0.048mm2 3mW synthesizable fractional-N PLL with a soft injection-locking technique

A Compact, Low-Power and Low-Jitter Dual-Loop Injection Locked PLL Using All-Digital PVT Calibration

A 0.4-Ps-jitter −52-Dbc-spur Synthesizable Injection-Locked PLL with Self-Clocked Nonoverlap Update and Slope-Balanced Subsampling BBPD

A 0.0055mm2 480µw Fully Synthesizable PLL Using Stochastic TDC in 28nm FDSOI

A Fully-Synthesizable Fractional-N Injection-Locked PLL for Digital Clocking with Triangle/Sawtooth Spread-Spectrum Modulation Capability in 5-Nm CMOS

An HDL-synthesized Injection-Locked PLL Using LC-based DCO for On-Chip Clock Generation

A 0.0055 Mm(2) 480 Mu W Fully Synthesizable Pll Using Stochastic Tdc In 28 Nm Fdsoi

A Dual-Loop Injection-Locked PLL with All-Digital Background Calibration System for On-Chip Clock Generation

A 1.2ps-jitter fully-synthesizable fully-calibrated fractional-N injection-locked PLL using true arbitrary nonlinearity calibration technique

A 0.001-Mm$$^{2}$$ 112.32-$$\Upmu $$W All-Digital PLL with Dual-Tuned DCO and Dual-Tuned Control Algorithm

A 0.022mm2 970µw Dual-Loop Injection-Locked PLL with −243db FOM Using Synthesizable All-Digital PVT Calibration Circuits

A 1.6&#x2013;880mhz Synthesizable ADPLL in 0.13um CMOS

A 2.2 Ghz-242 Db-Fom 4.2 Mw Adc-Pll Using Digital Sub-Sampling Architecture

25.2 A 2.2ghz &Amp;#x2212;242db-Fom 4.2mw ADC-PLL Using Digital Sub-Sampling Architecture