Abstract:As humanity is confronted by climate change, electrochemical CO 2 reduction has become an important strategy for generating value-added chemicals whilst lowering carbon emissions. In this work, Cu 2 O nanoparticles with different morphologies and predominant exposed crystal facets, including nanocubes (Cu 2 O-NC) with (100) facets, nanoflowers (Cu 2 O-NF) with (110) facets, and octahedral structures (Cu 2 O-O) with (111) facets, are prepared, and compared as catalysts for the electrochemical CO 2 reduction to C 2+ products in a flow cell electrolyzer, to overcome the mass transfer limitations of CO 2 in an H-cell and reach industrially relevant currents. To maximize the performance towards C 2+ products, a parameter optimization ( i.e. pH and current) was performed. Under the conditions of 150 mA cm −2 and pH of 8.5, the Cu 2 O-NC revealed a maximum faradaic efficiency of 58% for C 2+ products. Similar studies in an H-cell system have shown lower total C 2+ FE of around 35–40% for the nanocubes, indicating an improvement and showcasing the advantages of using a gas-fed flow electrolyzer. Finally, the long-term stability of these materials was also evaluated. The results revealed that C 2+ activity remains constant for four hours at 50%. However, a sharp decline was observed after five hours when GDE flooding occurs, leading to a dominant HER. To confirm, the electrode was washed and dried before re-utilizing it. Since the Cu 2 O largely recovers its initial C 2+ activity (from 50% to 43%) albeit with a slightly different product composition, this confirms GDE flooding as the main cause of degradation. During the eCO 2 RR, Cu 2 O is reduced to metallic Cu, as proven by in situ Raman. As a result, the particle morphology is roughened, which is proven by ex situ SEM images. Subsequently, water penetrates the gas diffusion electrode more easily, inhibiting the diffusion of CO 2 , and alongside the electrowetting effect results in GDE flooding. In conclusion, this work explores the utilization of different Cu 2 O catalysts in a flow electrolyzer, revealing insights into higher currents, their stability issues, crystal facet dependency, and reaction environment, which was unexplored in previous literature where the focus was on H-cell testing, which evaluates the catalysts under less demanding and more controlled conditions that are less relevant for up-scaling and eventual commercialization. Based on these new insights, further improvements can be made to enhance the total C 2+ FE and improve stability.

Impact of gas diffusion layer architecture on the performances of Cu-based electrodes for CO 2 electroreduction to ethylene in flow reactors

Gas diffusion in catalyst layer of flow cell for CO2 electroreduction toward C2+ products

Near-Electrode Concentration Gradients of Bicarbonate and pH within Porous Gas Diffusion Electrode for Optimized Selective CO2 Electroreduction to C2+ Products

Rational Designing Microenvironment of Gas‐Diffusion Electrodes via Microgel‐Augmented CO2 Availability for High‐Rate and Selective CO2 Electroreduction to Ethylene

From batch to flow: the effect of pH, current, and the crystal facets of Cu2O on electrochemical CO2 reduction

Additive-Assisted Electrodeposition of Cu on Gas Diffusion Electrodes Enables Selective CO 2 Reduction to Multicarbon Products

Additive-Assisted Electrodeposition of Cu on Gas Diffusion Electrodes Enables Selective CO2 Reduction to Multicarbon Products

Self-supported copper-based gas diffusion electrodes improve the local CO2 concentration for efficient electrochemical CO2 reduction

Gas Diffusion Electrodes (GDEs) for Carbon Dioxide (CO 2 ) Reduction in Microfluidic Cells: Towards a Fluid Dynamics Assisted Rational Design

Pore accessibility matters in CO 2 electrolysis: Preventing H 2 formation and boosting triple-phase boundary on microtubular gas-diffusion electrodes

Gas diffusion enhanced electrode with ultrathin superhydrophobic macropore structure for acidic CO 2 electroreduction

Introductory Guide to Assembling and Operating Gas Diffusion Electrodes for Electrochemical CO2 Reduction

Converting CO 2 to multi-carbon products at >1 A/cm 2 using gas diffusion electrode based on commercial materials via transfer process engineering

Porous Bilayer Electrode‐Guided Gas Diffusion for Enhanced CO 2 Electrochemical Reduction

A continuous flow reactor for tubular gas diffusion electrodes

Temperature-dependent selectivity for CO electroreduction on copper-based gas-diffusion electrodes at high current densities

High‐rate and Selective CO2 Electrolysis to Ethylene via Metal‐Organic Framework‐augmented CO2 Availability

Hydrophobicity Graded Gas Diffusion Layer for Stable Electrochemical Reduction of CO2

Engineering interfacial molecular interactions on Ag Hollow fibre gas diffusion electrodes for high efficiency in CO2 conversion to CO

Regulating the reaction zone of electrochemical CO2 reduction on gas-diffusion electrodes by distinctive hydrophilic-hydrophobic catalyst layers

Hierarchically Conductive Electrodes Unlock Stable and Scalable CO2 Electrolysis