Abstract:The higher voltage blocking capability and faster switching speed of silicon-carbide (SiC) mosfets have the potential to replace Si insulated gate bipolar transistors (IGBTs) in medium-low-voltage and high-power applications. In this paper, a state-of-the-art commercially available 325 A, 1700 V SiC mosfet module has been fully characterized under various load currents, bus voltages, and gate resistors to reveal their switching capability. Meanwhile, Si IGBT modules with similar power ratings are also tested under the same conditions. From the test results, several interesting points have been obtained: different to the Si IGBT module, the over-shoot current of the SiC mosfet module increases linearly with the increase of the load current and it has been explained by a model of the over-shoot current proposed in this paper; the induced negative gate voltage due to the complementary device turn-off (crosstalk effect) is more harmful to the SiC mosfet module than the induced positive gate voltage during turn-on when the gate off-voltage is 6 V; the maximum dvdt and didt (electromagnetic interference) during switching transients of the SiC mosfet module are close to those of the Si IGBT module when the gate resistance is larger than 8 but the switching loss of the SiC mosfet module is much smaller; the switching losses of the Si IGBT module are greater than those of the SiC mosfet module even when the gate resistance of the former is reduced to zero. An accurate power loss model, which is suitable for a three-phase two-level converter based on SiC mosfet modules considering the power loss of the parasitic capacitance, has been presented and verified in this paper. From the model, a 96.2 efficiency can be achieved at the switching frequency of 80kHz and the power of 100 kW.

An injection efficiency model to characterize the injection capability and turn-off speed for >10kV 4H-SiC IGBTs

The Injection Efficiency Controlled IGBT

A Hybrid-Channel Injection Enhanced Modulation 4H-SiC IGBT Transistors With Improved Performance

A New SiC Planar-Gate IGBT for Injection Enhancement Effect and Low Oxide Field

An Analytical Investigation of the Effect of Varied Buffer Layer Designs on the Turn-Off Speed for 4H-Sic Igbts

4H-Sic 15kv N-Igbt Physics-Based Sub-Circuit Model Implemented in Simulink/Matlab

Design and Characterization of High-Voltage 4H-Sic P-Igbts

Performance Evaluation of High-Power SiC MOSFET Modules in Comparison to Si IGBT Modules

A Numerical Method for Solving the Physics-Based Model of IGBT with All Free-Carrier Injection Conditions in the Base Region

Static and Dynamic Performance Characterization and Comparison of 15 Kv Sic Mosfet and 15 Kv Sic N-Igbts

IGBT Model for Analysis of Complicated Circuits

Design and Characterization of 10 kV High Voltage 4H-SiC p-Channel IGBTs with Low VF

A Physics‐based Turn off Model and Its Output‐characteristic Analysing Expressions of High‐voltage Soft‐punch Through IGBTs under Extreme SOA Conditions

Theoretical Analysis of ON-State Performance Limit of 4H-SiC IGBT in Field-Stop Technology

New Improvement Results on 7.5 Kv 4H-Sic P-Igbts with R<sub>diff, On</sub> of 26 M&#x003a9;·cm<sup>2</sup> at 25&Amp;#x000b0;c

A Novel 4H–SiC/Si Heterojunction IGBT Achieving Low Turn–Off Loss

A Survey on Modeling of SiC IGBT

New Improvement Results On 7.5 Kv 4h-Sic P-Igbts With R-Diff,R- On Of 26 M Omega-Cm(2) At 25 Degrees C

Enhancing Turn-off Performance in IGCT-Based High Power Applications—Part Ⅱ: Hybrid Switch with IGBT Integration and Experimental Validation

Gate Structure Design of SiC Trench IGBTs for Injection-Enhancement Effect