Abstract:A newly advanced heat-resistant steel SA-213 S31035 (22Cr25Ni3W3CuCoNbN), is currently the strongest commercially available austenitic heat resistant steel and has been recognized as one of the main candidate materials for A-USC plants operating at 700 °C. Up to now, the reason for which has excellent creep performance is not clear yet. In this paper, the S31035 steels were crept at 700 °C with applied stresses in the range of 140–220 MPa up to 15627 h, and during creep the microstructure evolution including the precipitation of second phases as well as their strengthening mechanisms were deeply investigated. Creep tests results show that S31035 steel has much higher creep strength than S30432 steel, with extrapolated creep rupture strength of about 118.0 MPa at 700 °C for 50,000 h. Furthermore, it has great rupture ductility with an area reduction of more than 50%. The excellent creep strength of S31035 steel was produced by the combined precipitation strengthening of nano-scaled Cu-rich phase, needle-shaped Laves phase, and secondary Z phase. The nano-scaled Cu-rich phase was very stable during long-time creep and acted as the dominant precipitation strengthening. Unlike the coarse and granular Laves phase in ferritic P92 steel (9CrW), the spindly needle-shaped Laves phase in austenitic S31035 steel could effectively impede the moving of dislocations and greatly increase the creep strength. And the coarsening of Laves phase in width was slight but in length was apparent, which was conducive to the strengthening effect. The fine secondary Z phase also showed relatively slow coarsening rate, contributed an important part of strengthening enhancement. The precipitation of detrimental σ phase is effectively suppressed through the increased content of Ni and the addition of Co. Besides, the grain-boundary sliding and grain rotation occurred during creep. Under high stresses (≥170 MPa) and short-time creep, intragranular cracks dominated the creep failure. The cracks preferred to produce inside the grains with higher Taylor factor which are hard to deform. Under relatively lower stresses (≤140 MPa), intergranular cracks dominated the creep failure and cracks mainly generate on the grain boundaries between the grains with greatly different deformations. The texture <111>//RD formed during creep, suppressing the proceeding plastic deform and improving the creep resistance. Under lower stress and long-time creep, a new texture <001>//RD occurred, which improves the creep rupture ductility of the S31035 steel.

A New Wrought Ni–Fe-base Superalloy for Advanced Ultra-Supercritical Power Plant Applications Beyond 700 °C

Microstructure and deformation mechanism of Ni-based wrought superalloys for A-USC power plants: a review

Alloy Design and Development of High Cr Containing FeCrAl Ferritic Alloys for Extreme Environments

Investigation of Precipitation Behavior of a Novel Ni-Fe-Based Superalloy during High-Temperature Aging Treatment

Creep Behavior and Deformation Mechanism of a Third-Generation Single Crystal Ni-Based Superalloy at 980 °C

Influence of Replacing Molybdenum with Tungsten on the Creep Fracture Property of Waspaloy Nickel-Based Alloy

Thermodynamic Evaluation and Composition Design of Candidate Alloys for 700 ℃ Class Ultra-supercritical Plant

Effects of boron addition on the microstructure and creep properties of a Ni-Fe-based superalloy weld metal alloy

Microstructure and Mechanical Properties of a Novel Powder Metallurgy Nickel-Base Superalloy

Design for 1200 °C creep properties of Ni-based single crystal superalloys: Effect of γ′-forming elements and its microscopic mechanism

Microstructural Stability and Creep Performance of a Novel Low-Cost Single Crystal Superalloy

Effect of Alloying Additions on Oxidation Behaviors of Ni‐Fe Based Superalloy for Ultra‐Supercritical Boiler Applications

Study on creep characteristics and the isochronous stress–strain curve of Ni-Cr-Mo superalloy

Towards Superior High Temperature Properties in Low Density AlCrFeNiTi Compositionally Complex Alloys

Tensile, Creep Behavior and Microstructure Evolution of an As-Cast Ni-based K417G Polycrystalline Superalloy

Investigation of the Fireside Corrosion of a New Wrought Ni-Fe-Cr-based Alloy in Advanced Ultra-Supercritical Steam Boilers

The Application of Grain Boundary Engineering to a Nickel Base Superalloy for 973 K (700 °C) USC Power Plants

Novel Cast Ni‐based Superalloys with Superb Weldability and Mechanical Properties Screened by a Multi‐Performance‐Oriented Criterion

New Research Development of Superalloy GH4169

The microstructure and mechanical performance optimization of a new Fe-Ni-based superalloy for gen IV nuclear reactor: The critical role of Nb alloying strategy

Strengthening mechanisms and creep rupture behavior of advanced austenitic heat resistant steel SA-213 S31035 for A-USC power plants