Abstract:With the increase in service temperature of aero-engine hot components, the requirements for the high-temperature performance and processability of the powder metallurgy (PM) superalloys used for preparing turbine disks also increase. To overcome the bottlenecks that constrain the preparation and microstructure control of PM superalloys, this work investigates the impacts of hot compression parameters on the hot deformation behavior and microstructure evolution of a novel PM superalloy, FGH4113A. Hot compression tests were conducted on the FGH4113A alloy, which underwent hot isostatic pressing, within a temperature range of 1050 °C–1150 °C and at a consistent true strain rate ranging from 0.001s −1 to 1s −1 . The results reveal that the flow stress decreases progressively with the reduction of strain rate and the rise in temperature. Optimal hot deformation conditions are identified at a temperature of 1110 °C with strain rates ranging from 0.1s −1 to 1s −1 , and a temperature of 1130 °C with strain rates between 0.01s −1 and 0.1s −1 . Within these optimal regimes, grains are uniform, and the average grain size is maintained within10μm. Grain evolution during hot compression involves original grain deformation, followed by recrystallization, subsequent grain coarsening, and then deformation again. Additionally, the γ′ area fraction diminishes with an increase in deformation temperature. Specifically, as the deformation temperature raises from 1050 °C to 1110 °C, and subsequently to 1150 °C, at a rate of 0.001s −1 , the primary γ′ area fraction diminishes progressively from 6.2 % to 3.0 % and ultimately to zero. Above 1130 °C, the γ′ area fraction remained largely unaffected by variations in strain rate. These insights are pivotal, offering both experimental data and theoretical perspectives for optimal microstructure control in PM superalloys.

Microstructure and Mechanical Properties of a Novel Powder Metallurgy Nickel-Base Superalloy

Microstructure and Mechanical Properties of New Third-Generation Nickel-Based Powder Superalloy

Microstructure and Mechanical Properties of Novel Nickel-Based P/M Superalloy

Hot deformation behavior and microstructure evolution of a novel nickel-based powder metallurgy superalloy

Influences of a Hot-Working Process on the Microstructural Evolution and Creep Performance of a Spray-Formed Nickel-Based Superalloy

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

Microstructure and Elevated Temperature Tensile Behaviour of Directionally Solidified Nickel Based Superalloy

Correlation between microstructure and mechanical properties of novel Co-Ni-based powder metallurgy superalloy

Tensile, Creep Behavior and Microstructure Evolution of an As-Cast Ni-based K417G Polycrystalline Superalloy

Effect of the Powder Size Distribution on the Hot Deformation Behavior of a Novel Nickel-based Powder Metallurgy Superalloy

Effect of Creep Process on the Microstructural Evolution and Deformation Behavior of a New Powder Metallurgy Ni-Based Superalloy

Study on Microstructure and Mechanical Properties of Single Crystal/powder Superalloy Pulsed Current Diffusion Bonded Joints

Processing, Microstructures and Mechanical Properties of a Ni-Based Single Crystal Superalloy

Microstructure and mechanical properties of a new nickel-based single crystal superalloy

Microstructure Evolution and Mechanical Performance of Nickel Based Superalloy C1023 at Elevated Temperatures

The Effect of Long-Term Aging on the Microstructure and Properties of a Novel Nickel-Based Powder Superalloy FGH4113A

Effects of stress and temperature on creep behavior of a new third-generation powder metallurgy superalloy FGH100L

Microstructure, crack formation and improvement on Nickel-based superalloy fabricated by powder bed fusion

Investigation of Precipitation Behavior of a Novel Ni-Fe-Based Superalloy during High-Temperature Aging Treatment

Thermal processing behaviour and microstructural evolution of high W and high γ' content extruded nickel-based powder metallurgy superalloy FGH4109

Phase constitution, microstructure and mechanical properties of a Ni-based superalloy specially designed for additive manufacturing