Abstract:With the increase in service temperature of aero-engine hot components, the requirements for the high-temperature performance and processability of the powder metallurgy (PM) superalloys used for preparing turbine disks also increase. To overcome the bottlenecks that constrain the preparation and microstructure control of PM superalloys, this work investigates the impacts of hot compression parameters on the hot deformation behavior and microstructure evolution of a novel PM superalloy, FGH4113A. Hot compression tests were conducted on the FGH4113A alloy, which underwent hot isostatic pressing, within a temperature range of 1050 °C–1150 °C and at a consistent true strain rate ranging from 0.001s −1 to 1s −1 . The results reveal that the flow stress decreases progressively with the reduction of strain rate and the rise in temperature. Optimal hot deformation conditions are identified at a temperature of 1110 °C with strain rates ranging from 0.1s −1 to 1s −1 , and a temperature of 1130 °C with strain rates between 0.01s −1 and 0.1s −1 . Within these optimal regimes, grains are uniform, and the average grain size is maintained within10μm. Grain evolution during hot compression involves original grain deformation, followed by recrystallization, subsequent grain coarsening, and then deformation again. Additionally, the γ′ area fraction diminishes with an increase in deformation temperature. Specifically, as the deformation temperature raises from 1050 °C to 1110 °C, and subsequently to 1150 °C, at a rate of 0.001s −1 , the primary γ′ area fraction diminishes progressively from 6.2 % to 3.0 % and ultimately to zero. Above 1130 °C, the γ′ area fraction remained largely unaffected by variations in strain rate. These insights are pivotal, offering both experimental data and theoretical perspectives for optimal microstructure control in PM superalloys.

New Research Development of Superalloy GH4169

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

Microstructure And Mechanical Properties Of Laser Melting Deposited Gh4169 Superalloy

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of Heat Treatment on the Microstructure of a Ni–Fe Based Superalloy for Advanced Ultra-Supercritical Power Plant Applications

Influence of Hot Corrosion on Precipitation of Phase and Tensile Properties of GH4169 Superalloy

Research on Tensile Properties of Ni-Base Super Alloy GH3128

The Effects of Microstructure on the Thermophysical Properties of the K439B Ni-Based Superalloy

Effects of High Gravity on the Nucleation and Precipitation of Ö Phase of GH4169 Alloy

Nano-twin-induced Exceptionally Superior Cryogenic Mechanical Properties of a Ni-based GH3536 (hastelloy X) Superalloy

Microstructural Evolution of Wrought-Nickel-Based Superalloy GH4169

Residual stress release and corresponding microstructural changes in high-energy impact-modified GH4169 after aging at 425 °C and 650 °C

Investigation of Precipitation Behavior of a Novel Ni-Fe-Based Superalloy during High-Temperature Aging Treatment

Difference of properties after heat treatment between GH4169 and GH3536 alloys fabricated by direct energy deposition

Tensile, Creep Behavior and Microstructure Evolution of an As-Cast Ni-based K417G Polycrystalline Superalloy

Influence of Various Heat Treatments on Microstructures and Mechanical Properties of GH4099 Superalloy Produced by Laser Powder Bed Fusion

Microstructural evolution of GH4079 superalloy during hot deformation and heat treatment

Hot deformation behavior and microstructure evolution of a novel nickel-based powder metallurgy superalloy

Thermal Stability of GH4065A Superalloy Based on Microstructural and Performance Evolution Following Long-Term Aging

Investigation of Solidification Behavior in a New High Alloy Ni-Based Superalloy