Abstract:In this work, the anisotropic tensile properties of laser additive manufactured (LAMed) GH4169 in as deposited and different heat-treated conditions are presented and the underlying mechanisms are analyzed in detail. Vertical and horizontal specimens for tensile tests were taken from as deposited (AD) and heat-treated blocks. Two heat treatment conditions with solution temperature of 980 °C and 1050 °C were considered. The tensile test results indicate different tensile properties of the vertical and horizontal samples, and such anisotropy is related to heat treatment conditions. The vertical AD sample has higher tensile strength than its horizontal counterpart, while after heat treatment, the horizontal direction shows higher tensile strength. Microstructure characterization, texture and grain morphology analyses were conducted through SEM with EBSD, XRD and TEM observations in order to figure out the main influential factors of the anisotropic tensile properties. Besides, fracture surfaces of the tensile specimens were observed to study the role of precipitates. In addition, the residual stresses in the LAMed samples in AD and heat-treated conditions were measured, and their effects on the anisotropic tensile strength were clarified by correlating the residual stress levels with the recrystallization fractions extracted from EBSD data. The obtained results show that a large number of brittle Laves phases growing along the vertical direction are distributed in the AD samples, which leads to different separation manners of Laves phase/γ matrix interfaces under different loading directions. Besides, the residuals stress level is high direction dependent in the AD samples. After heat treatment, most of the Laves phases are dissolved, and the residual stress experiences a significant variation. On the whole, the anisotropic tensile strength is mainly influenced by the residual stress level before and after heat treatment, and slightly influenced by the dissolution of the Laves phase. The present study provides a deeper understanding of the anisotropic tensile properties of LAMed GH4169, which may contribute to future engineering applications of Ni-based superalloys.

Microstructure And Mechanical Properties Of Laser Melting Deposited Gh4169 Superalloy

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

High-temperature Oxidation Behavior of AlCoCrCuFeNi High-Entropy Alloy by Selective Laser Melting

Influence of Various Heat Treatments on Microstructures and Mechanical Properties of GH4099 Superalloy Produced by Laser Powder Bed Fusion

Mechanism of High Temperature Mechanical Properties Enhancement of Ni-based Superalloys Repaired by Laser Directed Energy Deposition: Microstructure Analysis and Crystal Plasticity Simulation

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of Heat Treatment on Microstructure and High Temperature Tensile Mechanical Properties of Selective-Laser-Melted GH3230 Superalloy

Effect of Cast and Heat Treatment Processes on Microstructure and Properties of K4169 Superalloy

Laser Powder Bed Fusion of GH4099 Superalloy: Parameter Optimization and Effect of Heat Treatment on Microstructure and Mechanical Properties

Microstructure and Tensile Properties of High-Deposition-Rate Laser Metal Deposited GH4169 Alloy

A nickel-base superalloy with refined microstructures and excellent mechanical properties prepared by selective laser melting

A comprehensive study of the anisotropic tensile properties of laser additive manufactured Ni-based superalloy after heat treatment

Effect of Heat Treatment on Microstructure and Residual Stress of GH3536 Superalloy Fabricated by Selective Laser Melting

Microstructure and Mechanical Properties of Crack - Free Ni - Based Gh3536 Superalloy Fabricated by Laser Solid Forming

Effect of Heat Treatment on Microstructure and Mechanical Properties of a Selective Laser Melting Processed Ni-Based Superalloy GTD222

Difference of properties after heat treatment between GH4169 and GH3536 alloys fabricated by direct energy deposition

An Investigation of the Microstructural Evolution and Tensile Properties of a Nickel-Based GH648 Superalloy Manufactured Through Selective Laser Melting

Effects of Powder Feeding Rate on Microstructure and Mechanical Properties of GH4169

Microstructure and Mechanical Properties of GH4169D Superalloy Fabricated by Hybrid Arc and Micro-Rolling Additive Manufacturing

Influence of GH4169 Addition on Cracking Control, Microstructure and Mechanical Properties of GH4169 / K465 Composite Material Manufactured by Selective Laser Melting

Influence of Heat Treatment Temperature on Grain Structures and Properties of a Ni-based Superalloy Fabricated Via Selective Laser Melting