Abstract:The microstructures and mechanical properties of a γ'-strengthened nickel-based superalloy, GH4099, produced by laser powder bed fusion, at room temperature and 900 °C are investigated, followed by three various heat treatments. The as-built (AB) alloy consists of cellular/dendrite substructures within columnar grains aligning in <100> crystal orientation. No γ' phase is observed in the AB sample due to the relatively low content of Al +Ti. Following the standard solid solution treatment, the molten pool boundaries and cellular/dendrite substructures disappear, whilst the columnar grains remain. The transformation of columnar grains to equiaxed grains occurs through the primary solid solution treatment due to the recovery and recrystallization process. After aging at 850 °C for 480 min, the carbides in the three samples distributed at grain boundaries and within grains and the spherical γ' phase whose size is about 43 nm ± 16 nm develop in the standard solid solution + aging and primary solid solution + aging samples (SA and PA samples) while the bimodal size of cubic (181 nm ± 85 nm) and spherical (43 nm ± 16 nm) γ' precipitates is presented in the primary solid solution + secondary solid solution + aging sample (PSA samples). The uniaxial tensile tests are carried out at room temperature (RT) and 900 °C. The AB sample has the best RT ductility (~51% of elongation and ~67% of area reduction). Following the three heat treatments, the samples all acquire excellent RT tensile properties (>750 MPa of yield strengths and >32% of elongations). However, clear ductility dips and intergranular fracture modes occur during the 900 °C tensile tests, which could be related to carbide distribution and a change in the deformation mechanism.

Influence of Hot Corrosion on Precipitation of Phase and Tensile Properties of GH4169 Superalloy

Influence of temperature on hot corrosion behavior of GH4169 superalloy subjected to Na 2 SO 4 -NaCl salts attack

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

New Research Development of Superalloy GH4169

Temperature Dependence in Tensile Properties and Deformation Behavior of GH4169 Alloy

Research on Hot Corrosion Behavior of DZ40M and K452 Superalloys in NaCl Molten Salt

Microstructural evolution of GH4079 superalloy during hot deformation and heat treatment

Effects of Heat Treatment on the Microstructure and Properties of a Cast Nickel-Based High-Cr Superalloy

Influence of Cr Content on Hot Corrosion and a Special Tube Sealing Test of Single Crystal Nickel Base Superalloy

Influence of Various Heat Treatments on Microstructures and Mechanical Properties of GH4099 Superalloy Produced by Laser Powder Bed Fusion

Effect of microstructure on hot corrosion behavior of new superalloy Ad 730 in 75 wt% Na2SO4 + 25 wt% NaCl molten salt

The microstructure evolution and its effect on the mechanical properties of a hot-corrosion resistant Ni-based superalloy during long-term thermal exposure

High Temperature Corrosion of Two Superalloys in the Impure Helium Environment

A Study of the Hot Salt Corrosion Behavior of Three Nickel-Based Single-Crystal Superalloys at 900 °C

Influence of heat treatment on Inconel 625 superalloy sheet: carbides, γ'', δ phase precipitation and tensile deformation behavior

Corrosion behavior and mechanism of GH3535 alloy in NaOH, HF and H2O2 solution

Influence of alloying elements on hot corrosion resistance of nickel-based single crystal superalloys coated with Na2SO4 salt at 900 °C

Revealing internal corrosion of GH4169 with stress coupled solid NaCl deposited in a humid environment of 600 °C

Hot corrosion behaviors of directed energy deposited Inconel 718/Haynes 25 functionally graded material at 700 °C and 900 °C

Effects of High Gravity on the Nucleation and Precipitation of Ö Phase of GH4169 Alloy