Abstract:Microporous and mesoporous activated carbon produced from longan-seed biomass were impregnated with NaOH and used to capture CO 2 from a simulated flue gas in a fixed-bed column. The process variables that were studied included types of activated carbon as characterized by the volume ratio of micropores and mesopores (V mic /V mes ), adsorption temperature, NaOH loading, gas feed rate and the adsorbent amount. All five process variables affected the two important breakthrough parameters, namely the breakthrough time (t B ) and CO 2 adsorption capacity at breakthrough time (q B ), with different trends and degrees. However, it was only the NaOH loading that showed a characteristic of an optimum loading that provided the maximum of the breakthrough parameters. It was found that an approximate 45% increase in the adsorbed amount of CO 2 could be achieved with the activated carbon impregnated with around 1 weight % NaOH solution as compared to the case of the non-impregnated carbon. The response surface methodology (RSM) was applied to develop the correlations for both t B and q B and the maximum predicted q B of 33.58 mg/g was derived at the NaOH loading of 76.5 mg/g carbon, V mic /V mes of 2.83, adsorption temperature of 20°C, gas feed rate of 156 kg/m 2 -h and adsorbent amount of 51 kg/m 2 of column cross-section area. The Klinkenberg's breakthrough model was able to describe the CO 2 breakthrough curves reasonably well for all the tested conditions. The analysis of the two model parameters, the affinity constant (K) and the effective pore diffusivity (D e ), revealed that the optimum V mic /V mes that provided the maximum K value was around 2.90, corresponding to the activated carbon that contains 74% and 26% by volume of micropores and mesopores, respectively. The proper volume ratio of micropores and mesopores along with alkali addition into activated carbon can be effectively used for maximizing CO 2 adsorption in a fixed-bed adsorption system.

Experimental Study of Breakthrough Adsorption on Activated Carbon for CO2 Capture

A basic study on the nano CaO-based CO2 adsorbents in FFB for CO2 capture

Post-combustion CO2 capture from a natural gas combined cycle power plant using activated carbon adsorption

The Application of Biochar for CO2 Capture: Influence of Biochar Preparation and CO2 Capture Reactors.

Effect of Water on CO<inf>2</inf> Adsorption with Activated Carbon

Design and development of 3D hierarchical ultra-microporous CO2-sieving carbon architectures for potential flow-through CO2 capture at typical practical flue gas temperatures

Comprehensive Analysis of Biochar-Based Co2 Capture

Simulation of Capturing Carbon Dioxide from Flue Gas by Activated Carbon

Dynamic of CO2 adsorption in a fixed bed of microporous and mesoporous activated carbon impregnated with sodium hydroxide and the application of response surface methodology (RSM) for determining optimal adsorption conditions

A High Adsorption Capacity Bamboo Biochar for CO2 Capture for Low Temperature Heat Utilization

Cost-effective carbon-based amine adsorbents for carbon capture: Equilibrium, kinetics and selectivity

Synthesis and characterization of high-performance activated carbon from walnut shell biomass for CO2 capture

Optimal Activation of Porous Carbon for High Performance CO2 Capture

Advances in Post‐Combustion CO 2 Capture by Physical Adsorption: From Materials Innovation to Separation Practice

Steam adsorption equilibrium data at 110°C on an activated carbon, Lewatit VP OC 1065, and CALF-20 using a microscale dynamic column breakthrough apparatus

Numerical simulation on adsorption of CO2 using K2CO3 particles in the bubbling fluidized bed

Elevated Pressure CO2 Adsorption Characteristics of K-promoted Hydrotalcites for Pre-combustion Carbon Capture

Porous Adsorption Materials for Carbon Dioxide Capture in Industrial Flue Gas

Evaluation of carbon dioxide–nitrogen separation through fixed bed measurements and simulations

Thermodynamics and Regeneration Studies of CO2 Adsorption on Activated Carbon

Coffee grounds derived N enriched microporous activated carbons: Efficient adsorbent for post-combustion CO2 capture and conversion